Hi, I'm using rel-20.06 software of starlingX-4.0. Initial connection happens to pxe server on controller-0. I do see some packets between worker node and controller-0. Below tcpdump shows those packets [root@controller-0 ~(keystone_admin)]# tcpdump -i any port 69 or port 53 or
port 67 -nn tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on any, link-type LINUX_SLL (Linux cooked), capture size 262144 bytes 10:42:58.263992 ethertype IPv4, IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from f0:d4:e2:e9:8e:c4, length 548 10:42:58.263992 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from f0:d4:e2:e9:8e:c4, length 548 10:42:58.264290 IP 192.168.22.102.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 305 10:42:58.264299 ethertype IPv4, IP 192.168.22.102.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 305 10:43:02.301357 ethertype IPv4, IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from f0:d4:e2:e9:8e:c4, length 548 10:43:02.301357 IP 0.0.0.0.68 > 255.255.255.255.67: BOOTP/DHCP, Request from f0:d4:e2:e9:8e:c4, length 548 10:43:02.310717 IP 192.168.22.102.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 305 10:43:02.310725 ethertype IPv4, IP 192.168.22.102.67 > 255.255.255.255.68: BOOTP/DHCP, Reply, length 305 10:43:02.311555 ethertype IPv4, IP 169.254.202.138.2070 > 169.254.202.1.69: 27 RRQ "pxelinux.0" octet tsize 0 10:43:02.311555 IP 169.254.202.138.2070 > 169.254.202.1.69: 27 RRQ "pxelinux.0" octet tsize 0 10:43:02.311927 ethertype IPv4, IP 169.254.202.138.2071 > 169.254.202.1.69: 32 RRQ "pxelinux.0" octet blksize 1456 10:43:02.311927 IP 169.254.202.138.2071 > 169.254.202.1.69: 32 RRQ "pxelinux.0" octet blksize 1456 10:43:02.358861 ethertype IPv4, IP 169.254.202.138.49152 > 169.254.202.1.69: 79 RRQ "pxelinux.cfg/44454c4c-4800-104c-8034-cac04f473333" octet tsize 0 blksize 1408 ..................
*10:43:40.347690 ethertype IPv4, IP 169.254.202.138.49156 > 169.254.202.1.69: 57 RRQ "rel-20.06/installer-bzImage" octet tsize 0 blksize 140810:43:40.347690 IP 169.254.202.138.49156 > 169.254.202.1.69: 57 RRQ "rel-20.06/installer-bzImage" octet tsize 0 blksize 140810:43:41.035183 ethertype IPv4, IP 169.254.202.138.49157 > 169.254.202.1.69: 56 RRQ "rel-20.06/installer-initrd" octet tsize 0 blksize 140810:43:41.035183 IP 169.254.202.138.49157 > 169.254.202.1.69: 56 RRQ "rel-20.06/installer-initrd" octet tsize 0 blksize 1408*
169.254.202.138 is the worker node ip and 169.254.202.1 is the controller-0 ip. Above 4 are the last packets exchanged and after that no communication is seen. Worker node does not proceed further in installation. Pxe network in the controller node is on vlan-143 and I have enabled the same vlan in bios of the worker node. Please let me know if any info is required. Regards, Sriram On Thu, Oct 1, 2020 at 1:25 PM Sriram <sriram.ec@gmail.com> wrote:
Hi,
I'm trying to bring up the edge cloud with 3 nodes (1 controller and 2 worker nodes) with starlingX 4.0 - distributed cloud. Central cloud is up and running with All in One Duplex 2 controller configuration.
I was able to bring up the controller-0 in edge cloud using iso (virtual cd/dvd mount) and was able to configure the personality for the other nodes as workers. But worker-0 and worker-1 are stuck in pxe boot for more than 2hrs. Any suggestions?
In "Standard controller with storage" configuration, is having 2 controllers compulsory ?
https://docs.starlingx.io/deploy_install_guides/r4_release/bare_metal/contro... This document says it supports 2 controllers and upto 10 worker nodes.
Regards, Sriram