Hi, I am trying to give the above mentioned ISO image a try on our ArteSyn/MaxCore box without success. After starting the installation I'll get the following message: [ 18.503656] localhost iscsid[643]: iSCSI daemon with pid=644 started! [ 18.503816] localhost iscsid[643]: can't open InitiatorName configuration file /etc/iscsi/initiatorname.iscsi [ 18.503949] localhost iscsid[643]: Warning: InitiatorName file /etc/iscsi/initiatorname.iscsi does not exist or does not contain a properly formatted InitiatorName. If using software iscsi (iscsi_tcp or ib_iser) or partial offload (bnx2i or cxgbi iscsi), you may not be able to log into or [ 18.504121] localhost iscsid[643]: can't open InitiatorAlias configuration file /etc/iscsi/initiatorname.iscsi [ 18.504254] localhost iscsid[643]: can't open iscsid.safe_logout configuration file /etc/iscsi/iscsid.conf [ 21.185105] localhost kernel: scsi 0:0:0:0: Direct-Access Generic Ultra HS-COMBO 1.98 PQ: 0 ANSI: 0 [ 21.204488] localhost kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk [ 18.665925] localhost multipathd[636]: sda: add path (uevent) [ 18.667242] localhost multipathd[636]: sda: failed to get path uid [ 18.667399] localhost multipathd[636]: uevent trigger error [ 21.930592] localhost kernel: scsi 1:0:0:0: Direct-Access TrekStor TrekStor USB CS PQ: 0 ANSI: 0 CCS [ 21.940187] localhost kernel: scsi 1:0:0:0: alua: supports implicit and explicit TPGS [ 21.947210] localhost kernel: scsi 1:0:0:0: alua: No target port descriptors found [ 21.953921] localhost kernel: scsi 1:0:0:0: alua: not attached [ 21.959034] localhost kernel: sd 1:0:0:0: [sdb] 15257600 512-byte logical blocks: (7.81 GB/7.27 GiB) [ 21.968220] localhost kernel: sd 1:0:0:0: [sdb] Write Protect is off [ 21.973575] localhost kernel: sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 21.974314] localhost kernel: sd 1:0:0:0: [sdb] No Caching mode page found [ 21.980260] localhost kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through [ 21.990203] localhost kernel: sdb: sdb1 [ 21.994973] localhost kernel: sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 19.533105] localhost multipathd[636]: sdb: add path (uevent) [ 63.961502] localhost kernel: random: crng init done [ 142.536373] localhost dracut-initqueue[646]: Warning: dracut-initqueue timeout - starting timeout scripts ... [ 203.386668] localhost dracut-initqueue[646]: Warning: Could not boot. [ 204.505706] localhost systemd[1]: Received SIGRTMIN+20 from PID 625 (plymouthd). [ 204.505980] localhost dracut-initqueue[646]: Warning: /dev/root does not exist [ 204.514883] localhost systemd[1]: Starting Dracut Emergency Shell... [ 204.532145] localhost systemd[1]: Received SIGRTMIN+21 from PID 625 (plymouthd). I suspect that the installer is not finding the disk, which is in our case nvme0n1 and nvme1n1 flash storage. Any idea or hint is welcome! Thanks Marcel