Hi Gupta:

      OK.  could you check why some pods is not running ?

kubectl get po -n openstack | grep ceilometer

if some pods are still Init or failed ?

you can check the dependence or events of the output of  “kubectl describe po ceilometer-xxxx -n openstack”

Thanks.

BR
Austin Sun.

From: Anirudh Gupta <Anirudh.Gupta@hsc.com>
Sent: Wednesday, November 6, 2019 11:43 AM
To: Sun, Austin <austin.sun@intel.com>; starlingx-discuss@lists.starlingx.io; starlingx-announce@lists.starlingx.io
Subject: RE: No Telemetry Service Installed in StarlingX 2.0

Hi Austin

I have enabled Ceilometer, Gnocchi and Aodh helm charts using the command suggested and then applied stx-openstack.

But now I am facing exception in deploying ceilometer chart.

There is timeout error in Ceilometer Pod.

Timed out waiting for pods (namespace=openstack, labels=(release_group=osh-openstack-ceilometer)). These pods were not ready=['ceilometer-notification-7548b6db79-fhzfq']

armada.exceptions.armada_exceptions.ChartDeployException: Exception deploying charts: ['openstack-ceilometer']

I am also attaching the logs for your reference.

Please suggest the alternative to resolve the issue.

Regards

Anirudh Gupta

From: Sun, Austin <austin.sun@intel.com>
Sent: 04 November 2019 19:16
To: Anirudh Gupta <Anirudh.Gupta@hsc.com>; starlingx-discuss@lists.starlingx.io; starlingx-announce@lists.starlingx.io
Subject: RE: No Telemetry Service Installed in StarlingX 2.0

Hi Gupta:

By default , telemetry services are disabled (chart is not enabled) ,  but you can enable it by command “system helm-chart-attribute-modify” to enable it.

Thanks.

BR
Austin Sun.

From: Anirudh Gupta <Anirudh.Gupta@hsc.com>
Sent: Monday, November 4, 2019 7:19 PM
To: starlingx-discuss@lists.starlingx.io; starlingx-announce@lists.starlingx.io
Subject: [Starlingx-discuss] No Telemetry Service Installed in StarlingX 2.0

Hi Team,

StarlingX 2.0 release doesn’t have any endpoint for any Telemetry services like Ceilometer, Gnocchi and Aodh, because of which we are unable to get the metric values corresponding to the VM’s being spawned of StarlingX.

However this was not the case with StarlingX 2018.10 release. It had all the support for Telemetry Services, from which I was able to get CPU_Util and Mem_util of the VM’s spawned.

It is a must requirement for my setup as I need to Auto scale my VNF’s based on the metric values.

Please suggest the ways to install it.

Regards

Anirudh Gupta

DISCLAIMER: This electronic message and all of its contents, contains information which is privileged, confidential or otherwise protected from disclosure. The information contained in this electronic mail transmission is intended for use only by the individual or entity to which it is addressed. If you are not the intended recipient or may have received this electronic mail transmission in error, please notify the sender immediately and delete / destroy all copies of this electronic mail transmission without disclosing, copying, distributing, forwarding, printing or retaining any part of it. Hughes Systique accepts no responsibility for loss or damage arising from the use of the information transmitted by this email including damage from virus.

DISCLAIMER: This electronic message and all of its contents, contains information which is privileged, confidential or otherwise protected from disclosure. The information contained in this electronic mail transmission is intended for use only by the individual or entity to which it is addressed. If you are not the intended recipient or may have received this electronic mail transmission in error, please notify the sender immediately and delete / destroy all copies of this electronic mail transmission without disclosing, copying, distributing, forwarding, printing or retaining any part of it. Hughes Systique accepts no responsibility for loss or damage arising from the use of the information transmitted by this email including damage from virus.