Hi,
I am facing the same issue w/ R2.0. The document link below recommends
to "write in ISO mode". Should rather be "write in DD Image mode"
https://docs.starlingx.io/deploy_install_guides/bootable_usb.html

Thanks & Regards
Pratik

On Fri, Jul 12, 2019 at 12:46 PM Lin, Shuicheng <shuicheng.lin@intel.com> wrote:
>
> Hi Gupta,
>
> For the 1st issue, please try to create the image in Linux system with cmd like below:
>
> sudo dd if=bootimage.iso of=/dev/sdb bs=1M && sync
>
> (sdb is the pen driver device)
>
>
>
> For the 2nd issue, StarlingX doesn’t support USB Ethernet in default. You need modify kernel configuration to support it if you want.
>
> Also StarlingX uses CentOS 7.6 with 3.10 kernel, which is a much old kernel. So not all usb Ethernet driver could be supported.
>
> Also there is other code need be updated to support USB Ethernet.
>
> You could have a try with below 2 patches applied:
>
> https://review.opendev.org/657291
>
> https://review.opendev.org/657313
>
> It will be much easier if you could add a PCI Ethernet card in your machine. J
>
>
>
> Best Regards
>
> Shuicheng
>
>
>
> From: Anirudh Gupta [mailto:Anirudh.Gupta@hsc.com]
> Sent: Wednesday, July 10, 2019 3:18 PM
> To: starlingx-discuss@lists.starlingx.io; starlingx-announce@lists.starlingx.io
> Subject: [Starlingx-discuss] StarlingX Bootimage.iso Queries
>
>
>
> Hi Team,
>
>
>
> I have tried installing StarlingX 2018.10 and 2019.05 on my Dell,HP,Supermicro Server/Machines, but facing the following issues:
>
>
>
> If I create a bootable pen drive and try to install the image, it give me the following error
>
>
>
>          dracut-initqueue[628]: Warning: dracut-initqueue timeout - starting timeout scripts
>
>          dracut-initqueue[628]: Warning: dracut-initqueue timeout - starting timeout scripts
>
>          dracut-initqueue[628]: Warning: dracut-initqueue timeout - starting timeout scripts
>
>
>
> And eventually enters into the Grub.
>
>
>
>                     dracut:/# _
>
> However this issue is not being faced when I install the Bootimage.iso by creating a bootable DVD.
>
>
>
> The image depicting the issue is attached in the mail.
>
>
>
> Is it compulsory to install bootimage.iso using CD/DVD only?
>
>
>
> The StarlingX is not able to detect USB to Ethernet NIC Adapter
>
>
>
> I have installed StarlingX in one of my machine which has only one on-board NIC. I have a USB to Ethernet available with me which is being detected on Windows/Linux.
>
> I have tested it with Windows Ubuntu Centos.
>
> But StarlingX is not able to detect it. It only detects the on-board NIC a machine has.
>
> Is it possible to detect USB to Ethernet NIC in StarlingX?
>
>
>
>
>
> Regards
>
> Anirudh Gupta
>
> DISCLAIMER: This electronic message and all of its contents, contains information which is privileged, confidential or otherwise protected from disclosure. The information contained in this electronic mail transmission is intended for use only by the individual or entity to which it is addressed. If you are not the intended recipient or may have received this electronic mail transmission in error, please notify the sender immediately and delete / destroy all copies of this electronic mail transmission without disclosing, copying, distributing, forwarding, printing or retaining any part of it. Hughes Systique accepts no responsibility for loss or damage arising from the use of the information transmitted by this email including damage from virus.
>
> _______________________________________________
> Starlingx-discuss mailing list
> Starlingx-discuss@lists.starlingx.io
> http://lists.starlingx.io/cgi-bin/mailman/listinfo/starlingx-discuss

_______________________________________________
Starlingx-discuss mailing list
Starlingx-discuss@lists.starlingx.io
http://lists.starlingx.io/cgi-bin/mailman/listinfo/starlingx-discuss