Additional information: We are using the following iso: http://mirror.starlingx.cengn.ca/mirror/starlingx/master/centos/20190109T162... Marcel

------------------------------

Message: 2 Date: Fri, 1 Feb 2019 16:31:35 +0100 (CET) From: Marcel Schaible <marcel@schaible-consulting.de> To: starlingx-discuss@lists.starlingx.io Subject: [Starlingx-discuss] Installation problem: Configuration failed: Failed to update hiera configuration Message-ID: <1484346064.187533.1549035095571@communicator.strato.com> Content-Type: text/plain; charset=UTF-8

Hi,

during installation when appling the configuration I'll get an error message from hiera:

Configuration failed: Failed to update hiera configuration

Configuration log and apply_manifet.log is attached below.

Any idea or hint?

Thanks

Marcel

localhost:~# config_controller System Configuration ==================== Enter Q at any prompt to abort...

System date and time: ---------------------

The system date and time must be set now. Note that UTC time must be used and that the date and time must be set as accurately as possible, even if NTP/PTP is to be configured later.

Current system date and time (UTC): 2019-02-01 15:15:25

Is the current date and time correct? [y/n]: y Current system date and time will be used.

System timezone: ----------------

The system timezone must be set now. The timezone must be a valid timezone from /usr/share/zoneinfo (e.g. UTC, Asia/Hong_Kong, etc...)

Please input the timezone[UTC]:Europe/Berlin

System Configuration: ---------------------

System mode. Available options are:

1) duplex-direct - two node redundant configuration. Management and infrastructure networks are directly connected to peer ports 2) duplex - two node redundant configuration. 3) simplex - single node non-redundant configuration. System mode [duplex-direct]:

PXEBoot Network: ----------------

The PXEBoot network is used for initial booting and installation of each node. IP addresses on this network are reachable only within the data center.

The default configuration combines the PXEBoot network and the management network. If a separate PXEBoot network is used, it will share the management interface, which requires the management network to be placed on a VLAN.

Configure a separate PXEBoot network [y/N]: Aborting configuration localhost:~# config_controller System Configuration ==================== Enter Q at any prompt to abort...

System date and time: ---------------------

The system date and time must be set now. Note that UTC time must be used and that the date and time must be set as accurately as possible, even if NTP/PTP is to be configured later.

Current system date and time (UTC): 2019-02-01 15:15:40

Is the current date and time correct? [y/n]: y Current system date and time will be used.

System timezone: ----------------

The system timezone must be set now. The timezone must be a valid timezone from /usr/share/zoneinfo (e.g. UTC, Asia/Hong_Kong, etc...)

Please input the timezone[UTC]:Europe/Berlin

System Configuration: ---------------------

System mode. Available options are:

1) duplex-direct - two node redundant configuration. Management and infrastructure networks are directly connected to peer ports 2) duplex - two node redundant configuration. 3) simplex - single node non-redundant configuration. System mode [duplex-direct]: 1

PXEBoot Network: ----------------

The PXEBoot network is used for initial booting and installation of each node. IP addresses on this network are reachable only within the data center.

The default configuration combines the PXEBoot network and the management network. If a separate PXEBoot network is used, it will share the management interface, which requires the management network to be placed on a VLAN.

Configure a separate PXEBoot network [y/N]: N

Management Network: -------------------

The management network is used for internal communication between platform components. IP addresses on this network are reachable only within the data center.

A management bond interface provides redundant connections for the management network. It is strongly recommended to configure Management interface link aggregation, for All-in-one duplex-direct.

Management interface link aggregation [y/N]: y Management interface [bond0]: Management interface MTU [1500]:

Specify one of the bonding policies. Possible values are: 1) 802.3ad (LACP) policy 2) Active-backup policy

Management interface bonding policy [802.3ad]: A maximum of 2 physical interfaces can be attached to the management interface.

First management interface member [enp3s0f1]: enp8s20f4 Second management interface member []: enp8s20f5 Management subnet [192.168.204.0/24]: 172.27.1.0/24 Use entire management subnet [Y/n]: Y

IP addresses can be assigned to hosts dynamically or a static IP address can be specified for each host. This choice applies to both the management network and infrastructure network (if configured). Warning: Selecting 'N', or static IP address allocation, disables automatic provisioning of new hosts in System Inventory, requiring the user to manually provision using the 'system host-add' command. Dynamic IP address allocation [Y/n]: Y Management Network Multicast subnet [239.1.1.0/28]:

Infrastructure Network: -----------------------

The infrastructure network is used for internal communication between platform components to offload the management network of high bandwidth services. IP addresses on this network are reachable only within the data center.

If a separate infrastructure interface is not configured the management network will be used.

It is NOT recommended to configure infrastructure network for All-in- one duplex-direct. Configure an infrastructure interface [y/N]: N

External OAM Network: ---------------------

The external OAM network is used for management of the cloud. It also provides access to the platform APIs. IP addresses on this network are reachable outside the data center.

An external OAM bond interface provides redundant connections for the OAM network.

External OAM interface link aggregation [y/N]: y External OAM interface [bond1]: Configure an external OAM VLAN [y/N]: External OAM interface MTU [1500]:

Specify one of the bonding policies. Possible values are: 1) Active-backup policy 2) Balanced XOR policy 3) 802.3ad (LACP) policy

External OAM interface bonding policy [active-backup]: A maximum of 2 physical interfaces can be attached to the external OAM interface.

First external OAM interface member [enp3s0f0]: enp7s16f1 Second external oam interface member []: enp7s16f7 External OAM subnet [10.10.10.0/24]: 10.62.150.0/24 External OAM gateway address [10.62.150.1]: External OAM floating address [10.62.150.2]: External OAM address for first controller node [10.62.150.3]: 10.62.150.210 External OAM address for second controller node [10.62.150.211]:

Cloud Authentication: -------------------------------

Configure a password for the Cloud admin user The Password must have a minimum length of 7 character, and conform to password complexity rules Create admin user password: Repeat admin user password:

The following configuration will be applied:

System Configuration -------------------- Time Zone: Europe/Berlin System mode: duplex-direct

PXEBoot Network Configuration ----------------------------- Separate PXEBoot network not configured PXEBoot Controller floating hostname: pxecontroller

Management Network Configuration -------------------------------- Management interface name: bond0 Management interface: bond0 Management interface MTU: 1500 Management ae member 0: enp8s20f4 Management ae member 1: enp8s20f5 Management ae policy : 802.3ad Management subnet: 172.27.1.0/24 Controller floating address: 172.27.1.2 Controller 0 address: 172.27.1.3 Controller 1 address: 172.27.1.4 NFS Management Address 1: 172.27.1.5 NFS Management Address 2: 172.27.1.6 Controller floating hostname: controller Controller hostname prefix: controller- OAM Controller floating hostname: oamcontroller Dynamic IP address allocation is selected Management multicast subnet: 239.1.1.0/28

Infrastructure Network Configuration ------------------------------------ Infrastructure interface not configured

External OAM Network Configuration ---------------------------------- External OAM interface name: bond1 External OAM interface: bond1 External OAM interface MTU: 1500 External OAM ae member 0: enp7s16f1 External OAM ae member 1: enp7s16f7 External OAM ae policy : active-backup External OAM subnet: 10.62.150.0/24 External OAM gateway address: 10.62.150.1 External OAM floating address: 10.62.150.2 External OAM 0 address: 10.62.150.210 External OAM 1 address: 10.62.150.211

Apply the above configuration? [y/n]: y

Applying configuration (this will take several minutes):

01/08: Creating bootstrap configuration ... DONE 02/08: Applying bootstrap manifest ... DONE 03/08: Persisting local configuration ... DONE 04/08: Populating initial system inventory ... DONE 05/08: Creating system configuration ... sysinv 2019-02-01 15:20:44.053 25508 CRITICAL sysinv [-] 24 2019-02-01 15:20:44.053 25508 TRACE sysinv Traceback (most recent call last): 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/bin/sysinv-puppet", line 10, in <module> 2019-02-01 15:20:44.053 25508 TRACE sysinv sys.exit(main()) 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/cmd/puppet.py", line 75, in main 2019-02-01 15:20:44.053 25508 TRACE sysinv CONF.action.func(CONF.action.path, CONF.action.hostname) 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/cmd/puppet.py", line 47, in create_host_config_action 2019-02-01 15:20:44.053 25508 TRACE sysinv operator.update_host_config(host) 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/puppet.py", line 30, in _wrapper 2019-02-01 15:20:44.053 25508 TRACE sysinv func(self, *args, **kwargs) 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/puppet.py", line 145, in update_host_config 2019-02-01 15:20:44.053 25508 TRACE sysinv config.update(puppet_plugin.obj.get_host_config(host)) 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 99, in get_host_config 2019-02-01 15:20:44.053 25508 TRACE sysinv generate_interface_configs(context, config) 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 1029, in generate_interface_configs 2019-02-01 15:20:44.053 25508 TRACE sysinv generate_network_config(context, config, iface) 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 924, in generate_network_config 2019-02-01 15:20:44.053 25508 TRACE sysinv network_config = get_interface_network_config(context, iface) 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 896, in get_interface_network_config 2019-02-01 15:20:44.053 25508 TRACE sysinv os_ifname = get_interface_os_ifname(context, iface) 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 507, in get_interface_os_ifname 2019-02-01 15:20:44.053 25508 TRACE sysinv os_ifname = get_interface_port_name(context, iface) 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 472, in get_interface_port_name 2019-02-01 15:20:44.053 25508 TRACE sysinv port = get_interface_port(context, iface) 2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 464, in get_interface_port 2019-02-01 15:20:44.053 25508 TRACE sysinv return context['ports'][iface['id']] 2019-02-01 15:20:44.053 25508 TRACE sysinv KeyError: 24 2019-02-01 15:20:44.053 25508 TRACE sysinv Failed to update puppet hiera host config

Configuration failed: Failed to update hiera configuration localhost:~#

/tmp/apply_manifest.log: ========================

cp: cannot stat ‘/tmp/hieradata/172.27.1.3.yaml’: No such file or directory cp: cannot stat ‘/tmp/hieradata/system.yaml’: No such file or directory cp: cannot stat ‘/tmp/hieradata/secure_system.yaml’: No such file or directory Applying puppet bootstrap manifest... [DONE]

ls /tmp/puppet/hieradata/ ========================= global.yaml personality.yaml secure_static.yaml static.yaml localhost:~#