[Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore
Hi, I am trying to give the above mentioned ISO image a try on our ArteSyn/MaxCore box without success. After starting the installation I'll get the following message: [ 18.503656] localhost iscsid[643]: iSCSI daemon with pid=644 started! [ 18.503816] localhost iscsid[643]: can't open InitiatorName configuration file /etc/iscsi/initiatorname.iscsi [ 18.503949] localhost iscsid[643]: Warning: InitiatorName file /etc/iscsi/initiatorname.iscsi does not exist or does not contain a properly formatted InitiatorName. If using software iscsi (iscsi_tcp or ib_iser) or partial offload (bnx2i or cxgbi iscsi), you may not be able to log into or [ 18.504121] localhost iscsid[643]: can't open InitiatorAlias configuration file /etc/iscsi/initiatorname.iscsi [ 18.504254] localhost iscsid[643]: can't open iscsid.safe_logout configuration file /etc/iscsi/iscsid.conf [ 21.185105] localhost kernel: scsi 0:0:0:0: Direct-Access Generic Ultra HS-COMBO 1.98 PQ: 0 ANSI: 0 [ 21.204488] localhost kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk [ 18.665925] localhost multipathd[636]: sda: add path (uevent) [ 18.667242] localhost multipathd[636]: sda: failed to get path uid [ 18.667399] localhost multipathd[636]: uevent trigger error [ 21.930592] localhost kernel: scsi 1:0:0:0: Direct-Access TrekStor TrekStor USB CS PQ: 0 ANSI: 0 CCS [ 21.940187] localhost kernel: scsi 1:0:0:0: alua: supports implicit and explicit TPGS [ 21.947210] localhost kernel: scsi 1:0:0:0: alua: No target port descriptors found [ 21.953921] localhost kernel: scsi 1:0:0:0: alua: not attached [ 21.959034] localhost kernel: sd 1:0:0:0: [sdb] 15257600 512-byte logical blocks: (7.81 GB/7.27 GiB) [ 21.968220] localhost kernel: sd 1:0:0:0: [sdb] Write Protect is off [ 21.973575] localhost kernel: sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 21.974314] localhost kernel: sd 1:0:0:0: [sdb] No Caching mode page found [ 21.980260] localhost kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through [ 21.990203] localhost kernel: sdb: sdb1 [ 21.994973] localhost kernel: sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 19.533105] localhost multipathd[636]: sdb: add path (uevent) [ 63.961502] localhost kernel: random: crng init done [ 142.536373] localhost dracut-initqueue[646]: Warning: dracut-initqueue timeout - starting timeout scripts ... [ 203.386668] localhost dracut-initqueue[646]: Warning: Could not boot. [ 204.505706] localhost systemd[1]: Received SIGRTMIN+20 from PID 625 (plymouthd). [ 204.505980] localhost dracut-initqueue[646]: Warning: /dev/root does not exist [ 204.514883] localhost systemd[1]: Starting Dracut Emergency Shell... [ 204.532145] localhost systemd[1]: Received SIGRTMIN+21 from PID 625 (plymouthd). I suspect that the installer is not finding the disk, which is in our case nvme0n1 and nvme1n1 flash storage. Any idea or hint is welcome! Thanks Marcel
I just checked the latest CENGN ISO, and it's still using the unmodified installer image. See attached email thread. Scott, any update on this issue? -----Original Message----- From: Marcel Schaible [mailto:marcel@schaible-consulting.de] Sent: Wednesday, January 09, 2019 10:24 AM To: starlingx-discuss@lists.starlingx.io Subject: [Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore Hi, I am trying to give the above mentioned ISO image a try on our ArteSyn/MaxCore box without success. After starting the installation I'll get the following message: [ 18.503656] localhost iscsid[643]: iSCSI daemon with pid=644 started! [ 18.503816] localhost iscsid[643]: can't open InitiatorName configuration file /etc/iscsi/initiatorname.iscsi [ 18.503949] localhost iscsid[643]: Warning: InitiatorName file /etc/iscsi/initiatorname.iscsi does not exist or does not contain a properly formatted InitiatorName. If using software iscsi (iscsi_tcp or ib_iser) or partial offload (bnx2i or cxgbi iscsi), you may not be able to log into or [ 18.504121] localhost iscsid[643]: can't open InitiatorAlias configuration file /etc/iscsi/initiatorname.iscsi [ 18.504254] localhost iscsid[643]: can't open iscsid.safe_logout configuration file /etc/iscsi/iscsid.conf [ 21.185105] localhost kernel: scsi 0:0:0:0: Direct-Access Generic Ultra HS-COMBO 1.98 PQ: 0 ANSI: 0 [ 21.204488] localhost kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk [ 18.665925] localhost multipathd[636]: sda: add path (uevent) [ 18.667242] localhost multipathd[636]: sda: failed to get path uid [ 18.667399] localhost multipathd[636]: uevent trigger error [ 21.930592] localhost kernel: scsi 1:0:0:0: Direct-Access TrekStor TrekStor USB CS PQ: 0 ANSI: 0 CCS [ 21.940187] localhost kernel: scsi 1:0:0:0: alua: supports implicit and explicit TPGS [ 21.947210] localhost kernel: scsi 1:0:0:0: alua: No target port descriptors found [ 21.953921] localhost kernel: scsi 1:0:0:0: alua: not attached [ 21.959034] localhost kernel: sd 1:0:0:0: [sdb] 15257600 512-byte logical blocks: (7.81 GB/7.27 GiB) [ 21.968220] localhost kernel: sd 1:0:0:0: [sdb] Write Protect is off [ 21.973575] localhost kernel: sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 21.974314] localhost kernel: sd 1:0:0:0: [sdb] No Caching mode page found [ 21.980260] localhost kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through [ 21.990203] localhost kernel: sdb: sdb1 [ 21.994973] localhost kernel: sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 19.533105] localhost multipathd[636]: sdb: add path (uevent) [ 63.961502] localhost kernel: random: crng init done [ 142.536373] localhost dracut-initqueue[646]: Warning: dracut-initqueue timeout - starting timeout scripts ... [ 203.386668] localhost dracut-initqueue[646]: Warning: Could not boot. [ 204.505706] localhost systemd[1]: Received SIGRTMIN+20 from PID 625 (plymouthd). [ 204.505980] localhost dracut-initqueue[646]: Warning: /dev/root does not exist [ 204.514883] localhost systemd[1]: Starting Dracut Emergency Shell... [ 204.532145] localhost systemd[1]: Received SIGRTMIN+21 from PID 625 (plymouthd). I suspect that the installer is not finding the disk, which is in our case nvme0n1 and nvme1n1 flash storage. Any idea or hint is welcome! Thanks Marcel _______________________________________________ Starlingx-discuss mailing list Starlingx-discuss@lists.starlingx.io http://lists.starlingx.io/cgi-bin/mailman/listinfo/starlingx-discuss
Fix as of this image ... http://mirror.starlingx.cengn.ca/mirror/starlingx/master/centos/20190109T162... <http://mirror.starlingx.cengn.ca/mirror/starlingx/master/centos/20190109T162801Z/outputs/iso/bootimage.iso> On 2019-01-09 11:08 a.m., Penney, Don wrote:
I just checked the latest CENGN ISO, and it's still using the unmodified installer image. See attached email thread.
Scott, any update on this issue?
-----Original Message----- From: Marcel Schaible [mailto:marcel@schaible-consulting.de] Sent: Wednesday, January 09, 2019 10:24 AM To: starlingx-discuss@lists.starlingx.io Subject: [Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore
Hi,
I am trying to give the above mentioned ISO image a try on our ArteSyn/MaxCore box without success.
After starting the installation I'll get the following message:
[ 18.503656] localhost iscsid[643]: iSCSI daemon with pid=644 started! [ 18.503816] localhost iscsid[643]: can't open InitiatorName configuration file /etc/iscsi/initiatorname.iscsi [ 18.503949] localhost iscsid[643]: Warning: InitiatorName file /etc/iscsi/initiatorname.iscsi does not exist or does not contain a properly formatted InitiatorName. If using software iscsi (iscsi_tcp or ib_iser) or partial offload (bnx2i or cxgbi iscsi), you may not be able to log into or [ 18.504121] localhost iscsid[643]: can't open InitiatorAlias configuration file /etc/iscsi/initiatorname.iscsi [ 18.504254] localhost iscsid[643]: can't open iscsid.safe_logout configuration file /etc/iscsi/iscsid.conf [ 21.185105] localhost kernel: scsi 0:0:0:0: Direct-Access Generic Ultra HS-COMBO 1.98 PQ: 0 ANSI: 0 [ 21.204488] localhost kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk [ 18.665925] localhost multipathd[636]: sda: add path (uevent) [ 18.667242] localhost multipathd[636]: sda: failed to get path uid [ 18.667399] localhost multipathd[636]: uevent trigger error [ 21.930592] localhost kernel: scsi 1:0:0:0: Direct-Access TrekStor TrekStor USB CS PQ: 0 ANSI: 0 CCS [ 21.940187] localhost kernel: scsi 1:0:0:0: alua: supports implicit and explicit TPGS [ 21.947210] localhost kernel: scsi 1:0:0:0: alua: No target port descriptors found [ 21.953921] localhost kernel: scsi 1:0:0:0: alua: not attached [ 21.959034] localhost kernel: sd 1:0:0:0: [sdb] 15257600 512-byte logical blocks: (7.81 GB/7.27 GiB) [ 21.968220] localhost kernel: sd 1:0:0:0: [sdb] Write Protect is off [ 21.973575] localhost kernel: sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 21.974314] localhost kernel: sd 1:0:0:0: [sdb] No Caching mode page found [ 21.980260] localhost kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through [ 21.990203] localhost kernel: sdb: sdb1 [ 21.994973] localhost kernel: sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 19.533105] localhost multipathd[636]: sdb: add path (uevent) [ 63.961502] localhost kernel: random: crng init done [ 142.536373] localhost dracut-initqueue[646]: Warning: dracut-initqueue timeout - starting timeout scripts ... [ 203.386668] localhost dracut-initqueue[646]: Warning: Could not boot. [ 204.505706] localhost systemd[1]: Received SIGRTMIN+20 from PID 625 (plymouthd). [ 204.505980] localhost dracut-initqueue[646]: Warning: /dev/root does not exist [ 204.514883] localhost systemd[1]: Starting Dracut Emergency Shell... [ 204.532145] localhost systemd[1]: Received SIGRTMIN+21 from PID 625 (plymouthd).
I suspect that the installer is not finding the disk, which is in our case nvme0n1 and nvme1n1 flash storage.
Any idea or hint is welcome!
Thanks
Marcel
_______________________________________________ Starlingx-discuss mailing list Starlingx-discuss@lists.starlingx.io http://lists.starlingx.io/cgi-bin/mailman/listinfo/starlingx-discuss
Thanks Scott. From: Little, Scott Sent: Wednesday, January 09, 2019 3:55 PM To: Penney, Don; Marcel Schaible; starlingx-discuss@lists.starlingx.io Subject: Re: [Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore Fix as of this image ... http://mirror.starlingx.cengn.ca/mirror/starlingx/master/centos/20190109T162... On 2019-01-09 11:08 a.m., Penney, Don wrote: I just checked the latest CENGN ISO, and it's still using the unmodified installer image. See attached email thread. Scott, any update on this issue? -----Original Message----- From: Marcel Schaible [mailto:marcel@schaible-consulting.de] Sent: Wednesday, January 09, 2019 10:24 AM To: starlingx-discuss@lists.starlingx.io<mailto:starlingx-discuss@lists.starlingx.io> Subject: [Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore Hi, I am trying to give the above mentioned ISO image a try on our ArteSyn/MaxCore box without success. After starting the installation I'll get the following message: [ 18.503656] localhost iscsid[643]: iSCSI daemon with pid=644 started! [ 18.503816] localhost iscsid[643]: can't open InitiatorName configuration file /etc/iscsi/initiatorname.iscsi [ 18.503949] localhost iscsid[643]: Warning: InitiatorName file /etc/iscsi/initiatorname.iscsi does not exist or does not contain a properly formatted InitiatorName. If using software iscsi (iscsi_tcp or ib_iser) or partial offload (bnx2i or cxgbi iscsi), you may not be able to log into or [ 18.504121] localhost iscsid[643]: can't open InitiatorAlias configuration file /etc/iscsi/initiatorname.iscsi [ 18.504254] localhost iscsid[643]: can't open iscsid.safe_logout configuration file /etc/iscsi/iscsid.conf [ 21.185105] localhost kernel: scsi 0:0:0:0: Direct-Access Generic Ultra HS-COMBO 1.98 PQ: 0 ANSI: 0 [ 21.204488] localhost kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk [ 18.665925] localhost multipathd[636]: sda: add path (uevent) [ 18.667242] localhost multipathd[636]: sda: failed to get path uid [ 18.667399] localhost multipathd[636]: uevent trigger error [ 21.930592] localhost kernel: scsi 1:0:0:0: Direct-Access TrekStor TrekStor USB CS PQ: 0 ANSI: 0 CCS [ 21.940187] localhost kernel: scsi 1:0:0:0: alua: supports implicit and explicit TPGS [ 21.947210] localhost kernel: scsi 1:0:0:0: alua: No target port descriptors found [ 21.953921] localhost kernel: scsi 1:0:0:0: alua: not attached [ 21.959034] localhost kernel: sd 1:0:0:0: [sdb] 15257600 512-byte logical blocks: (7.81 GB/7.27 GiB) [ 21.968220] localhost kernel: sd 1:0:0:0: [sdb] Write Protect is off [ 21.973575] localhost kernel: sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 21.974314] localhost kernel: sd 1:0:0:0: [sdb] No Caching mode page found [ 21.980260] localhost kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through [ 21.990203] localhost kernel: sdb: sdb1 [ 21.994973] localhost kernel: sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 19.533105] localhost multipathd[636]: sdb: add path (uevent) [ 63.961502] localhost kernel: random: crng init done [ 142.536373] localhost dracut-initqueue[646]: Warning: dracut-initqueue timeout - starting timeout scripts ... [ 203.386668] localhost dracut-initqueue[646]: Warning: Could not boot. [ 204.505706] localhost systemd[1]: Received SIGRTMIN+20 from PID 625 (plymouthd). [ 204.505980] localhost dracut-initqueue[646]: Warning: /dev/root does not exist [ 204.514883] localhost systemd[1]: Starting Dracut Emergency Shell... [ 204.532145] localhost systemd[1]: Received SIGRTMIN+21 from PID 625 (plymouthd). I suspect that the installer is not finding the disk, which is in our case nvme0n1 and nvme1n1 flash storage. Any idea or hint is welcome! Thanks Marcel _______________________________________________ Starlingx-discuss mailing list Starlingx-discuss@lists.starlingx.io<mailto:Starlingx-discuss@lists.starlingx.io> http://lists.starlingx.io/cgi-bin/mailman/listinfo/starlingx-discuss
Hi, the image lloks better. At least I am getting now the installer screen. Now I am getting the following error: <--- snipp ---> anaconda 21.48.22.121-1 for CentOS 7 started. * installation log files are stored in /tmp during the installation * shell is available on TTY2 * when reporting a bug add logs from /tmp as separate text/plain attachments 02:17:51 Running pre-installation scripts There was an error running the kickstart script at line 256. This is a fatal error and installation will be aborted. The details of this error are: Installation failed. ERROR: Specified installation (sda) or boot (sda) device is a USB drive. <--- snipp ---> Question: How can I confugure the installation/root device? I my case I have 2 1TB nvme flash drives. Thanks for your help in advance Marcel
Scott Little <scott.little@windriver.com> hat am 9. Januar 2019 um 21:54 geschrieben:
Fix as of this image ...
http://mirror.starlingx.cengn.ca/mirror/starlingx/master/centos/20190109T162... <http://mirror.starlingx.cengn.ca/mirror/starlingx/master/centos/20190109T162801Z/outputs/iso/bootimage.iso>
On 2019-01-09 11:08 a.m., Penney, Don wrote:
I just checked the latest CENGN ISO, and it's still using the unmodified installer image. See attached email thread.
Scott, any update on this issue?
-----Original Message----- From: Marcel Schaible [mailto:marcel@schaible-consulting.de] Sent: Wednesday, January 09, 2019 10:24 AM To: starlingx-discuss@lists.starlingx.io Subject: [Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore
Hi,
I am trying to give the above mentioned ISO image a try on our ArteSyn/MaxCore box without success.
After starting the installation I'll get the following message:
[ 18.503656] localhost iscsid[643]: iSCSI daemon with pid=644 started! [ 18.503816] localhost iscsid[643]: can't open InitiatorName configuration file /etc/iscsi/initiatorname.iscsi [ 18.503949] localhost iscsid[643]: Warning: InitiatorName file /etc/iscsi/initiatorname.iscsi does not exist or does not contain a properly formatted InitiatorName. If using software iscsi (iscsi_tcp or ib_iser) or partial offload (bnx2i or cxgbi iscsi), you may not be able to log into or [ 18.504121] localhost iscsid[643]: can't open InitiatorAlias configuration file /etc/iscsi/initiatorname.iscsi [ 18.504254] localhost iscsid[643]: can't open iscsid.safe_logout configuration file /etc/iscsi/iscsid.conf [ 21.185105] localhost kernel: scsi 0:0:0:0: Direct-Access Generic Ultra HS-COMBO 1.98 PQ: 0 ANSI: 0 [ 21.204488] localhost kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk [ 18.665925] localhost multipathd[636]: sda: add path (uevent) [ 18.667242] localhost multipathd[636]: sda: failed to get path uid [ 18.667399] localhost multipathd[636]: uevent trigger error [ 21.930592] localhost kernel: scsi 1:0:0:0: Direct-Access TrekStor TrekStor USB CS PQ: 0 ANSI: 0 CCS [ 21.940187] localhost kernel: scsi 1:0:0:0: alua: supports implicit and explicit TPGS [ 21.947210] localhost kernel: scsi 1:0:0:0: alua: No target port descriptors found [ 21.953921] localhost kernel: scsi 1:0:0:0: alua: not attached [ 21.959034] localhost kernel: sd 1:0:0:0: [sdb] 15257600 512-byte logical blocks: (7.81 GB/7.27 GiB) [ 21.968220] localhost kernel: sd 1:0:0:0: [sdb] Write Protect is off [ 21.973575] localhost kernel: sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 21.974314] localhost kernel: sd 1:0:0:0: [sdb] No Caching mode page found [ 21.980260] localhost kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through [ 21.990203] localhost kernel: sdb: sdb1 [ 21.994973] localhost kernel: sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 19.533105] localhost multipathd[636]: sdb: add path (uevent) [ 63.961502] localhost kernel: random: crng init done [ 142.536373] localhost dracut-initqueue[646]: Warning: dracut-initqueue timeout - starting timeout scripts ... [ 203.386668] localhost dracut-initqueue[646]: Warning: Could not boot. [ 204.505706] localhost systemd[1]: Received SIGRTMIN+20 from PID 625 (plymouthd). [ 204.505980] localhost dracut-initqueue[646]: Warning: /dev/root does not exist [ 204.514883] localhost systemd[1]: Starting Dracut Emergency Shell... [ 204.532145] localhost systemd[1]: Received SIGRTMIN+21 from PID 625 (plymouthd).
I suspect that the installer is not finding the disk, which is in our case nvme0n1 and nvme1n1 flash storage.
Any idea or hint is welcome!
Thanks
Marcel
_______________________________________________ Starlingx-discuss mailing list Starlingx-discuss@lists.starlingx.io http://lists.starlingx.io/cgi-bin/mailman/listinfo/starlingx-discuss
Hi Marcel, When you're at the boot option you want to choose from the installer menu, hit <tab> to edit the boot command-line and modify the boot_device and rootfs_device parameters from the default sda to the correct device name (ie. nvme0n1). Cheers, Don. -----Original Message----- From: Marcel Schaible [mailto:marcel@schaible-consulting.de] Sent: Monday, January 14, 2019 10:00 AM To: Little, Scott; Penney, Don; starlingx-discuss@lists.starlingx.io Subject: Re: [Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore Hi, the image lloks better. At least I am getting now the installer screen. Now I am getting the following error: <--- snipp ---> anaconda 21.48.22.121-1 for CentOS 7 started. * installation log files are stored in /tmp during the installation * shell is available on TTY2 * when reporting a bug add logs from /tmp as separate text/plain attachments 02:17:51 Running pre-installation scripts There was an error running the kickstart script at line 256. This is a fatal error and installation will be aborted. The details of this error are: Installation failed. ERROR: Specified installation (sda) or boot (sda) device is a USB drive. <--- snipp ---> Question: How can I confugure the installation/root device? I my case I have 2 1TB nvme flash drives. Thanks for your help in advance Marcel
Scott Little <scott.little@windriver.com> hat am 9. Januar 2019 um 21:54 geschrieben:
Fix as of this image ...
http://mirror.starlingx.cengn.ca/mirror/starlingx/master/centos/20190109T162... <http://mirror.starlingx.cengn.ca/mirror/starlingx/master/centos/20190109T162801Z/outputs/iso/bootimage.iso>
On 2019-01-09 11:08 a.m., Penney, Don wrote:
I just checked the latest CENGN ISO, and it's still using the unmodified installer image. See attached email thread.
Scott, any update on this issue?
-----Original Message----- From: Marcel Schaible [mailto:marcel@schaible-consulting.de] Sent: Wednesday, January 09, 2019 10:24 AM To: starlingx-discuss@lists.starlingx.io Subject: [Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore
Hi,
I am trying to give the above mentioned ISO image a try on our ArteSyn/MaxCore box without success.
After starting the installation I'll get the following message:
[ 18.503656] localhost iscsid[643]: iSCSI daemon with pid=644 started! [ 18.503816] localhost iscsid[643]: can't open InitiatorName configuration file /etc/iscsi/initiatorname.iscsi [ 18.503949] localhost iscsid[643]: Warning: InitiatorName file /etc/iscsi/initiatorname.iscsi does not exist or does not contain a properly formatted InitiatorName. If using software iscsi (iscsi_tcp or ib_iser) or partial offload (bnx2i or cxgbi iscsi), you may not be able to log into or [ 18.504121] localhost iscsid[643]: can't open InitiatorAlias configuration file /etc/iscsi/initiatorname.iscsi [ 18.504254] localhost iscsid[643]: can't open iscsid.safe_logout configuration file /etc/iscsi/iscsid.conf [ 21.185105] localhost kernel: scsi 0:0:0:0: Direct-Access Generic Ultra HS-COMBO 1.98 PQ: 0 ANSI: 0 [ 21.204488] localhost kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk [ 18.665925] localhost multipathd[636]: sda: add path (uevent) [ 18.667242] localhost multipathd[636]: sda: failed to get path uid [ 18.667399] localhost multipathd[636]: uevent trigger error [ 21.930592] localhost kernel: scsi 1:0:0:0: Direct-Access TrekStor TrekStor USB CS PQ: 0 ANSI: 0 CCS [ 21.940187] localhost kernel: scsi 1:0:0:0: alua: supports implicit and explicit TPGS [ 21.947210] localhost kernel: scsi 1:0:0:0: alua: No target port descriptors found [ 21.953921] localhost kernel: scsi 1:0:0:0: alua: not attached [ 21.959034] localhost kernel: sd 1:0:0:0: [sdb] 15257600 512-byte logical blocks: (7.81 GB/7.27 GiB) [ 21.968220] localhost kernel: sd 1:0:0:0: [sdb] Write Protect is off [ 21.973575] localhost kernel: sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 21.974314] localhost kernel: sd 1:0:0:0: [sdb] No Caching mode page found [ 21.980260] localhost kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through [ 21.990203] localhost kernel: sdb: sdb1 [ 21.994973] localhost kernel: sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 19.533105] localhost multipathd[636]: sdb: add path (uevent) [ 63.961502] localhost kernel: random: crng init done [ 142.536373] localhost dracut-initqueue[646]: Warning: dracut-initqueue timeout - starting timeout scripts ... [ 203.386668] localhost dracut-initqueue[646]: Warning: Could not boot. [ 204.505706] localhost systemd[1]: Received SIGRTMIN+20 from PID 625 (plymouthd). [ 204.505980] localhost dracut-initqueue[646]: Warning: /dev/root does not exist [ 204.514883] localhost systemd[1]: Starting Dracut Emergency Shell... [ 204.532145] localhost systemd[1]: Received SIGRTMIN+21 from PID 625 (plymouthd).
I suspect that the installer is not finding the disk, which is in our case nvme0n1 and nvme1n1 flash storage.
Any idea or hint is welcome!
Thanks
Marcel
_______________________________________________ Starlingx-discuss mailing list Starlingx-discuss@lists.starlingx.io http://lists.starlingx.io/cgi-bin/mailman/listinfo/starlingx-discuss
Hi Don, ok, it worked. Is it also possible to use a raid like /dev/md for installation and booting? Thanks Marcel
"Penney, Don" <Don.Penney@windriver.com> hat am 14. Januar 2019 um 16:05 geschrieben:
Hi Marcel,
When you're at the boot option you want to choose from the installer menu, hit <tab> to edit the boot command-line and modify the boot_device and rootfs_device parameters from the default sda to the correct device name (ie. nvme0n1).
Cheers, Don.
-----Original Message----- From: Marcel Schaible [mailto:marcel@schaible-consulting.de] Sent: Monday, January 14, 2019 10:00 AM To: Little, Scott; Penney, Don; starlingx-discuss@lists.starlingx.io Subject: Re: [Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore
Hi,
the image lloks better. At least I am getting now the installer screen.
Now I am getting the following error:
<--- snipp ---> anaconda 21.48.22.121-1 for CentOS 7 started. * installation log files are stored in /tmp during the installation * shell is available on TTY2 * when reporting a bug add logs from /tmp as separate text/plain attachments 02:17:51 Running pre-installation scripts
There was an error running the kickstart script at line 256. This is a fatal error and installation will be aborted. The details of this error are:
Installation failed.
ERROR: Specified installation (sda) or boot (sda) device is a USB drive. <--- snipp --->
Question: How can I confugure the installation/root device? I my case I have 2 1TB nvme flash drives.
Thanks for your help in advance
Marcel
Scott Little <scott.little@windriver.com> hat am 9. Januar 2019 um 21:54 geschrieben:
Fix as of this image ...
http://mirror.starlingx.cengn.ca/mirror/starlingx/master/centos/20190109T162... <http://mirror.starlingx.cengn.ca/mirror/starlingx/master/centos/20190109T162801Z/outputs/iso/bootimage.iso>
On 2019-01-09 11:08 a.m., Penney, Don wrote:
I just checked the latest CENGN ISO, and it's still using the unmodified installer image. See attached email thread.
Scott, any update on this issue?
-----Original Message----- From: Marcel Schaible [mailto:marcel@schaible-consulting.de] Sent: Wednesday, January 09, 2019 10:24 AM To: starlingx-discuss@lists.starlingx.io Subject: [Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore
Hi,
I am trying to give the above mentioned ISO image a try on our ArteSyn/MaxCore box without success.
After starting the installation I'll get the following message:
[ 18.503656] localhost iscsid[643]: iSCSI daemon with pid=644 started! [ 18.503816] localhost iscsid[643]: can't open InitiatorName configuration file /etc/iscsi/initiatorname.iscsi [ 18.503949] localhost iscsid[643]: Warning: InitiatorName file /etc/iscsi/initiatorname.iscsi does not exist or does not contain a properly formatted InitiatorName. If using software iscsi (iscsi_tcp or ib_iser) or partial offload (bnx2i or cxgbi iscsi), you may not be able to log into or [ 18.504121] localhost iscsid[643]: can't open InitiatorAlias configuration file /etc/iscsi/initiatorname.iscsi [ 18.504254] localhost iscsid[643]: can't open iscsid.safe_logout configuration file /etc/iscsi/iscsid.conf [ 21.185105] localhost kernel: scsi 0:0:0:0: Direct-Access Generic Ultra HS-COMBO 1.98 PQ: 0 ANSI: 0 [ 21.204488] localhost kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk [ 18.665925] localhost multipathd[636]: sda: add path (uevent) [ 18.667242] localhost multipathd[636]: sda: failed to get path uid [ 18.667399] localhost multipathd[636]: uevent trigger error [ 21.930592] localhost kernel: scsi 1:0:0:0: Direct-Access TrekStor TrekStor USB CS PQ: 0 ANSI: 0 CCS [ 21.940187] localhost kernel: scsi 1:0:0:0: alua: supports implicit and explicit TPGS [ 21.947210] localhost kernel: scsi 1:0:0:0: alua: No target port descriptors found [ 21.953921] localhost kernel: scsi 1:0:0:0: alua: not attached [ 21.959034] localhost kernel: sd 1:0:0:0: [sdb] 15257600 512-byte logical blocks: (7.81 GB/7.27 GiB) [ 21.968220] localhost kernel: sd 1:0:0:0: [sdb] Write Protect is off [ 21.973575] localhost kernel: sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00 [ 21.974314] localhost kernel: sd 1:0:0:0: [sdb] No Caching mode page found [ 21.980260] localhost kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through [ 21.990203] localhost kernel: sdb: sdb1 [ 21.994973] localhost kernel: sd 1:0:0:0: [sdb] Attached SCSI removable disk [ 19.533105] localhost multipathd[636]: sdb: add path (uevent) [ 63.961502] localhost kernel: random: crng init done [ 142.536373] localhost dracut-initqueue[646]: Warning: dracut-initqueue timeout - starting timeout scripts ... [ 203.386668] localhost dracut-initqueue[646]: Warning: Could not boot. [ 204.505706] localhost systemd[1]: Received SIGRTMIN+20 from PID 625 (plymouthd). [ 204.505980] localhost dracut-initqueue[646]: Warning: /dev/root does not exist [ 204.514883] localhost systemd[1]: Starting Dracut Emergency Shell... [ 204.532145] localhost systemd[1]: Received SIGRTMIN+21 from PID 625 (plymouthd).
I suspect that the installer is not finding the disk, which is in our case nvme0n1 and nvme1n1 flash storage.
Any idea or hint is welcome!
Thanks
Marcel
_______________________________________________ Starlingx-discuss mailing list Starlingx-discuss@lists.starlingx.io http://lists.starlingx.io/cgi-bin/mailman/listinfo/starlingx-discuss
participants (3)
-
Marcel Schaible
-
Penney, Don
-
Scott Little