[Starlingx-discuss] Installation problem: Configuration failed: Failed to update hiera configuration
Peters, Matt
Matt.Peters at windriver.com
Fri Feb 1 16:07:31 UTC 2019
Hell Marcel,
If your system is still in that state, can you run the following commands?
source /etc/nova/openrc
system host-ethernet-port-list controller-0
system host-if-list -a controller-0
On 2019-02-01, 10:32 AM, "Marcel Schaible" <marcel at schaible-consulting.de> wrote:
Hi,
during installation when appling the configuration I'll get an error message from hiera:
Configuration failed: Failed to update hiera configuration
Configuration log and apply_manifet.log is attached below.
Any idea or hint?
Thanks
Marcel
localhost:~# config_controller
System Configuration
====================
Enter Q at any prompt to abort...
System date and time:
---------------------
The system date and time must be set now. Note that UTC time must be used and
that the date and time must be set as accurately as possible, even if NTP/PTP is
to be configured later.
Current system date and time (UTC): 2019-02-01 15:15:25
Is the current date and time correct? [y/n]: y
Current system date and time will be used.
System timezone:
----------------
The system timezone must be set now. The timezone must be a valid timezone from
/usr/share/zoneinfo (e.g. UTC, Asia/Hong_Kong, etc...)
Please input the timezone[UTC]:Europe/Berlin
System Configuration:
---------------------
System mode. Available options are:
1) duplex-direct - two node redundant configuration. Management and
infrastructure networks are directly connected to peer ports
2) duplex - two node redundant configuration.
3) simplex - single node non-redundant configuration.
System mode [duplex-direct]:
PXEBoot Network:
----------------
The PXEBoot network is used for initial booting and installation of each node.
IP addresses on this network are reachable only within the data center.
The default configuration combines the PXEBoot network and the management
network. If a separate PXEBoot network is used, it will share the management
interface, which requires the management network to be placed on a VLAN.
Configure a separate PXEBoot network [y/N]:
Aborting configuration
localhost:~# config_controller
System Configuration
====================
Enter Q at any prompt to abort...
System date and time:
---------------------
The system date and time must be set now. Note that UTC time must be used and
that the date and time must be set as accurately as possible, even if NTP/PTP is
to be configured later.
Current system date and time (UTC): 2019-02-01 15:15:40
Is the current date and time correct? [y/n]: y
Current system date and time will be used.
System timezone:
----------------
The system timezone must be set now. The timezone must be a valid timezone from
/usr/share/zoneinfo (e.g. UTC, Asia/Hong_Kong, etc...)
Please input the timezone[UTC]:Europe/Berlin
System Configuration:
---------------------
System mode. Available options are:
1) duplex-direct - two node redundant configuration. Management and
infrastructure networks are directly connected to peer ports
2) duplex - two node redundant configuration.
3) simplex - single node non-redundant configuration.
System mode [duplex-direct]: 1
PXEBoot Network:
----------------
The PXEBoot network is used for initial booting and installation of each node.
IP addresses on this network are reachable only within the data center.
The default configuration combines the PXEBoot network and the management
network. If a separate PXEBoot network is used, it will share the management
interface, which requires the management network to be placed on a VLAN.
Configure a separate PXEBoot network [y/N]: N
Management Network:
-------------------
The management network is used for internal communication between platform
components. IP addresses on this network are reachable only within the data
center.
A management bond interface provides redundant connections for the management
network.
It is strongly recommended to configure Management interface link
aggregation, for All-in-one duplex-direct.
Management interface link aggregation [y/N]: y
Management interface [bond0]:
Management interface MTU [1500]:
Specify one of the bonding policies. Possible values are:
1) 802.3ad (LACP) policy
2) Active-backup policy
Management interface bonding policy [802.3ad]:
A maximum of 2 physical interfaces can be attached to the management interface.
First management interface member [enp3s0f1]: enp8s20f4
Second management interface member []: enp8s20f5
Management subnet [192.168.204.0/24]: 172.27.1.0/24
Use entire management subnet [Y/n]: Y
IP addresses can be assigned to hosts dynamically or a static IP address can be
specified for each host. This choice applies to both the management network and
infrastructure network (if configured).
Warning: Selecting 'N', or static IP address allocation, disables automatic
provisioning of new hosts in System Inventory, requiring the user to manually
provision using the 'system host-add' command.
Dynamic IP address allocation [Y/n]: Y
Management Network Multicast subnet [239.1.1.0/28]:
Infrastructure Network:
-----------------------
The infrastructure network is used for internal communication between platform
components to offload the management network of high bandwidth services. IP
addresses on this network are reachable only within the data center.
If a separate infrastructure interface is not configured the management network
will be used.
It is NOT recommended to configure infrastructure network for All-in-
one duplex-direct.
Configure an infrastructure interface [y/N]: N
External OAM Network:
---------------------
The external OAM network is used for management of the cloud. It also provides
access to the platform APIs. IP addresses on this network are reachable outside
the data center.
An external OAM bond interface provides redundant connections for the OAM
network.
External OAM interface link aggregation [y/N]: y
External OAM interface [bond1]:
Configure an external OAM VLAN [y/N]:
External OAM interface MTU [1500]:
Specify one of the bonding policies. Possible values are:
1) Active-backup policy
2) Balanced XOR policy
3) 802.3ad (LACP) policy
External OAM interface bonding policy [active-backup]:
A maximum of 2 physical interfaces can be attached to the external OAM
interface.
First external OAM interface member [enp3s0f0]: enp7s16f1
Second external oam interface member []: enp7s16f7
External OAM subnet [10.10.10.0/24]: 10.62.150.0/24
External OAM gateway address [10.62.150.1]:
External OAM floating address [10.62.150.2]:
External OAM address for first controller node [10.62.150.3]: 10.62.150.210
External OAM address for second controller node [10.62.150.211]:
Cloud Authentication:
-------------------------------
Configure a password for the Cloud admin user The Password must have a minimum
length of 7 character, and conform to password complexity rules
Create admin user password:
Repeat admin user password:
The following configuration will be applied:
System Configuration
--------------------
Time Zone: Europe/Berlin
System mode: duplex-direct
PXEBoot Network Configuration
-----------------------------
Separate PXEBoot network not configured
PXEBoot Controller floating hostname: pxecontroller
Management Network Configuration
--------------------------------
Management interface name: bond0
Management interface: bond0
Management interface MTU: 1500
Management ae member 0: enp8s20f4
Management ae member 1: enp8s20f5
Management ae policy : 802.3ad
Management subnet: 172.27.1.0/24
Controller floating address: 172.27.1.2
Controller 0 address: 172.27.1.3
Controller 1 address: 172.27.1.4
NFS Management Address 1: 172.27.1.5
NFS Management Address 2: 172.27.1.6
Controller floating hostname: controller
Controller hostname prefix: controller-
OAM Controller floating hostname: oamcontroller
Dynamic IP address allocation is selected
Management multicast subnet: 239.1.1.0/28
Infrastructure Network Configuration
------------------------------------
Infrastructure interface not configured
External OAM Network Configuration
----------------------------------
External OAM interface name: bond1
External OAM interface: bond1
External OAM interface MTU: 1500
External OAM ae member 0: enp7s16f1
External OAM ae member 1: enp7s16f7
External OAM ae policy : active-backup
External OAM subnet: 10.62.150.0/24
External OAM gateway address: 10.62.150.1
External OAM floating address: 10.62.150.2
External OAM 0 address: 10.62.150.210
External OAM 1 address: 10.62.150.211
Apply the above configuration? [y/n]: y
Applying configuration (this will take several minutes):
01/08: Creating bootstrap configuration ... DONE
02/08: Applying bootstrap manifest ... DONE
03/08: Persisting local configuration ... DONE
04/08: Populating initial system inventory ... DONE
05/08: Creating system configuration ... sysinv 2019-02-01 15:20:44.053 25508 CRITICAL sysinv [-] 24
2019-02-01 15:20:44.053 25508 TRACE sysinv Traceback (most recent call last):
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/bin/sysinv-puppet", line 10, in <module>
2019-02-01 15:20:44.053 25508 TRACE sysinv sys.exit(main())
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/cmd/puppet.py", line 75, in main
2019-02-01 15:20:44.053 25508 TRACE sysinv CONF.action.func(CONF.action.path, CONF.action.hostname)
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/cmd/puppet.py", line 47, in create_host_config_action
2019-02-01 15:20:44.053 25508 TRACE sysinv operator.update_host_config(host)
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/puppet.py", line 30, in _wrapper
2019-02-01 15:20:44.053 25508 TRACE sysinv func(self, *args, **kwargs)
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/puppet.py", line 145, in update_host_config
2019-02-01 15:20:44.053 25508 TRACE sysinv config.update(puppet_plugin.obj.get_host_config(host))
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 99, in get_host_config
2019-02-01 15:20:44.053 25508 TRACE sysinv generate_interface_configs(context, config)
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 1029, in generate_interface_configs
2019-02-01 15:20:44.053 25508 TRACE sysinv generate_network_config(context, config, iface)
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 924, in generate_network_config
2019-02-01 15:20:44.053 25508 TRACE sysinv network_config = get_interface_network_config(context, iface)
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 896, in get_interface_network_config
2019-02-01 15:20:44.053 25508 TRACE sysinv os_ifname = get_interface_os_ifname(context, iface)
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 507, in get_interface_os_ifname
2019-02-01 15:20:44.053 25508 TRACE sysinv os_ifname = get_interface_port_name(context, iface)
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 472, in get_interface_port_name
2019-02-01 15:20:44.053 25508 TRACE sysinv port = get_interface_port(context, iface)
2019-02-01 15:20:44.053 25508 TRACE sysinv File "/usr/lib64/python2.7/site-packages/sysinv/puppet/interface.py", line 464, in get_interface_port
2019-02-01 15:20:44.053 25508 TRACE sysinv return context['ports'][iface['id']]
2019-02-01 15:20:44.053 25508 TRACE sysinv KeyError: 24
2019-02-01 15:20:44.053 25508 TRACE sysinv
Failed to update puppet hiera host config
Configuration failed: Failed to update hiera configuration
localhost:~#
/tmp/apply_manifest.log:
========================
cp: cannot stat ‘/tmp/hieradata/172.27.1.3.yaml’: No such file or directory
cp: cannot stat ‘/tmp/hieradata/system.yaml’: No such file or directory
cp: cannot stat ‘/tmp/hieradata/secure_system.yaml’: No such file or directory
Applying puppet bootstrap manifest...
[DONE]
ls /tmp/puppet/hieradata/
=========================
global.yaml personality.yaml secure_static.yaml static.yaml
localhost:~#
_______________________________________________
Starlingx-discuss mailing list
Starlingx-discuss at lists.starlingx.io
http://lists.starlingx.io/cgi-bin/mailman/listinfo/starlingx-discuss
More information about the Starlingx-discuss
mailing list