[Starlingx-discuss] [deploy-fail] Failed to deploy All-in-one simplex configuration
xiongzhiwei at baicells.com
xiongzhiwei at baicells.com
Tue Feb 19 07:16:39 UTC 2019
Hi Jaewook,
My ip setting is as below:
Actually, I had used three physical interface, enp2s0f0 is OAM inf with default ip 10.10.10.2/24, because it is not inconvenient in my operation room, so I had configured enp2s0f1 for my romote access.
I can access the dashboard both with ip 10.10.10.2 in lab and 192.168.107.232/22 in my operation room.
The third inf enp2s0f2 is used to data interface, I had created three VMs and network worked normally.
controller-0:~$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet 192.168.204.3/28 brd 192.168.204.15 scope host lo
valid_lft forever preferred_lft forever
inet 169.254.202.2/24 scope host lo
valid_lft forever preferred_lft forever
inet 192.168.204.2/28 scope host secondary lo
valid_lft forever preferred_lft forever
inet 192.168.204.5/28 scope host secondary lo
valid_lft forever preferred_lft forever
inet 192.168.204.10/28 scope host secondary lo
valid_lft forever preferred_lft forever
inet 192.168.204.6/28 scope host secondary lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: enp4s0f0: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default qlen 1000
link/ether 00:1b:21:bc:ff:a8 brd ff:ff:ff:ff:ff:ff
3: enp2s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether f8:75:88:6e:8f:e2 brd ff:ff:ff:ff:ff:ff
inet 10.10.10.2/24 brd 10.10.10.255 scope global enp2s0f0
valid_lft forever preferred_lft forever
inet6 fe80::fa75:88ff:fe6e:8fe2/64 scope link
valid_lft forever preferred_lft forever
4: enp2s0f1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
link/ether f8:75:88:6e:8f:e3 brd ff:ff:ff:ff:ff:ff
inet 192.168.107.232/22 brd 192.168.107.255 scope global enp2s0f1
valid_lft forever preferred_lft forever
inet6 fe80::fa75:88ff:fe6e:8fe3/64 scope link
valid_lft forever preferred_lft forever
6: enp2s0f3: <BROADCAST,MULTICAST> mtu 1500 qdisc mq state DOWN group default qlen 1000
link/ether f8:75:88:6e:8f:e5 brd ff:ff:ff:ff:ff:ff
7: ovs-netdev: <BROADCAST,PROMISC> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 8e:da:6c:1b:fd:15 brd ff:ff:ff:ff:ff:ff
8: br-int: <BROADCAST,PROMISC> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether f6:df:04:bf:a1:43 brd ff:ff:ff:ff:ff:ff
12: br-phy0: <BROADCAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN group default qlen 1000
link/ether f8:75:88:6e:8f:e4 brd ff:ff:ff:ff:ff:ff
inet6 fe80::fa75:88ff:fe6e:8fe4/64 scope link
valid_lft forever preferred_lft forever
13: lldp0d64ae5d-22: <BROADCAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN group default qlen 1000
link/ether 96:e0:03:51:17:6d brd ff:ff:ff:ff:ff:ff
inet6 fe80::94e0:3ff:fe51:176d/64 scope link
valid_lft forever preferred_lft forever
BR
Tim Xiong
From: Jaewook Oh
Date: 2019-02-19 15:00
To: xiongzhiwei at baicells.com
CC: starlingx-discuss; 오재욱
Subject: Re: [Starlingx-discuss] [deploy-fail] Failed to deploy All-in-one simplex configuration
Hello Tim,
thanks for your answer :)
However, still I cannot access to the dashboard.
I deployed StarlingX 3 times again, but the situation never changes..
If you don't mind, can I see your ip setting with (ip a command)?
Best Regards,
Jaewook.
2019년 2월 19일 (화) 오후 3:56, xiongzhiwei at baicells.com <xiongzhiwei at baicells.com>님이 작성:
Hi Jaewook,
I just finished stx all-in-one simplex on Bearmetal last week. The horizon service had been installed defaultly and you should be able to access the dashboard now.
Your service list is same as mine.
[wrsroot at controller-0 ~(keystone_admin)]$ openstack service list
+----------------------------------+------------+-----------------+
| ID | Name | Type |
+----------------------------------+------------+-----------------+
| c51dfde10adf4445a78113ad6e648b9a | barbican | key-manager |
| df07161f527b483292ac5aa5ed722687 | keystone | identity |
| 744183df128d414f97390fb70fcac72f | sysinv | platform |
| b9730f2e673443e4a6d003a7dad1d220 | fm | faultmanagement |
| 5d7855696b1f440b8401670e1df6cb28 | glance | image |
| 814a777c22884c97ab44baf0a4c2c669 | aodh | alarming |
| 68362243cc214c4181a15e583894e495 | placement | placement |
| 375cfb87c5f6449e81512ead128a513e | gnocchi | metric |
| 2643dadbe71b4fc68ad4daa7d9d3859f | nova | compute |
| f312a1c459c245c5a045c69688f695db | heat-cfn | cloudformation |
| cbf811729020470a81b3c7be0d453fc9 | neutron | network |
| 0fb46b24873648f9bac3a3e4d9f1f4e2 | patching | patching |
| 52db1ccfca9d4033be5f1180c50d8234 | ceilometer | metering |
| 094935b6dee245278bffc3f7ee21e9e9 | vim | nfv |
| bc5297541def4f8b8881254af9896824 | smapi | smapi |
| a388667479484a04824f07a672a331eb | panko | event |
| 8c982073cd6c4d04b6ecb49e76650d2c | heat | orchestration |
| 38c0b001ef514af5b1ba6947bed1bc6c | cinderv3 | volumev3 |
| 98699ea84e4543b6b0808e24395542bb | cinderv2 | volumev2 |
| 253390980b274178b7a16844e2c7a826 | cinder | volume |
+----------------------------------+------------+-----------------+
BR
Tim Xiong
From: Jaewook Oh
Date: 2019-02-19 12:48
To: starlingx-discuss; 오재욱
Subject: Re: [Starlingx-discuss] [deploy-fail] Failed to deploy All-in-one simplex configuration
Hello StarlingX Teams,
I found that the horizon dashboard project were not installed automatically when I deployed StarlingX all-in-one simplex on Baremetal.
Are there any reason for this problem..?
I used "2019-Feb-08 03:40:29 bootimage.iso".
[wrsroot at controller-0 ~(keystone_admin)]$ openstack service list
+----------------------------------+------------+-----------------+
| ID | Name | Type |
+----------------------------------+------------+-----------------+
| f8b821fdd8e44d8484a3521ade041340 | barbican | key-manager |
| 6f34b6874b624604a7f8798b95743dc4 | keystone | identity |
| d31b2325f40e4ce88ca6974ee852eff6 | sysinv | platform |
| cb68c2d74dc34caf91dfc92c9b099d22 | fm | faultmanagement |
| a7f2ae41f2ff45bd904012a0a53b63ec | glance | image |
| 3daea4e7507a4568a132579b4f30e4d6 | aodh | alarming |
| af6e9c3f185f498a8f8b7d1afaeaa06d | placement | placement |
| b1c2243ab7e24fe08bf408677a7f8e1d | gnocchi | metric |
| 0e21d579ddee4f2dbfe98ff4069ce321 | nova | compute |
| 15067bfe219b4645973f7399099c47da | heat-cfn | cloudformation |
| ecf3478c84334c2ba647740bde190739 | neutron | network |
| 28973cbc638c41c6b99b5e77264a2aec | patching | patching |
| a120d0d2ed0b45b39114e4e9cab5fd78 | ceilometer | metering |
| 12b32e4a181a4684ab05be02b3726d0c | vim | nfv |
| a9c28c1889a347359a9b77edf53e5833 | smapi | smapi |
| 2697e71aa8dc4f8b8d96c72b32c89440 | panko | event |
| 57a5cb58128445b5819747271c095a89 | heat | orchestration |
| 10c93aecb5a84278b940da2f8c3a1721 | cinderv3 | volumev3 |
| b569ff8b77364311bbf3a5dee38dd614 | cinderv2 | volumev2 |
| 449ceb89f8fe40779dd65c5a9c867161 | cinder | volume |
+----------------------------------+------------+-----------------+
I thought horizon should also be installed with StarlingX's deployment.
If not, please let me know how can I install horizon in this StarlingX.
Thanks for help in advance :)
Best Regards,
Jaewook.
2019년 2월 12일 (화) 오후 2:54, Jaewook Oh <kyle.oh95 at gmail.com>님이 작성:
Hello starlingx team,
I deployed Starlingx All-in-one simplex setting on my server,
it seems deployment was done well.
However I cannot access to the dashboard.
I used "2019-Feb-08 03:40:29 bootimage.iso".
Following log is the service that are now enabled,
[wrsroot at controller-0 ~(keystone_admin)]$ system service-list
+-----+-------------------------------+--------------+----------------+
| id | service_name | hostname | state |
+-----+-------------------------------+--------------+----------------+
| 68 | aodh-api | controller-0 | enabled-active |
| 69 | aodh-evaluator | controller-0 | enabled-active |
| 70 | aodh-listener | controller-0 | enabled-active |
| 71 | aodh-notifier | controller-0 | enabled-active |
| 102 | barbican-api | controller-0 | enabled-active |
| 103 | barbican-keystone-listener | controller-0 | enabled-active |
| 104 | barbican-worker | controller-0 | enabled-active |
| 43 | ceilometer-agent-notification | controller-0 | enabled-active |
| 14 | cgcs-export-fs | controller-0 | enabled-active |
| 10 | cgcs-fs | controller-0 | enabled-active |
| 16 | cgcs-nfs-ip | controller-0 | enabled-active |
| 35 | cinder-api | controller-0 | enabled-active |
| 38 | cinder-backup | controller-0 | enabled-active |
| 58 | cinder-ip | controller-0 | enabled-active |
| 56 | cinder-lvm | controller-0 | enabled-active |
| 36 | cinder-scheduler | controller-0 | enabled-active |
| 37 | cinder-volume | controller-0 | enabled-active |
| 23 | dnsmasq | controller-0 | enabled-active |
| 5 | drbd-cgcs | controller-0 | enabled-active |
| 55 | drbd-cinder | controller-0 | enabled-active |
| 75 | drbd-extension | controller-0 | enabled-active |
| 3 | drbd-pg | controller-0 | enabled-active |
| 6 | drbd-platform | controller-0 | enabled-active |
| 4 | drbd-rabbit | controller-0 | enabled-active |
| 77 | extension-export-fs | controller-0 | enabled-active |
| 76 | extension-fs | controller-0 | enabled-active |
| 24 | fm-mgr | controller-0 | enabled-active |
| 27 | glance-api | controller-0 | enabled-active |
| 26 | glance-registry | controller-0 | enabled-active |
| 108 | gnocchi-api | controller-0 | enabled-active |
| 109 | gnocchi-metricd | controller-0 | enabled-active |
| 62 | guest-agent | controller-0 | enabled-active |
| 64 | haproxy | controller-0 | enabled-active |
| 45 | heat-api | controller-0 | enabled-active |
| 46 | heat-api-cfn | controller-0 | enabled-active |
| 47 | heat-api-cloudwatch | controller-0 | enabled-active |
| 44 | heat-engine | controller-0 | enabled-active |
| 51 | horizon | controller-0 | enabled-active |
| 22 | hw-mon | controller-0 | enabled-active |
| 57 | iscsi | controller-0 | enabled-active |
| 25 | keystone | controller-0 | enabled-active |
| 50 | lighttpd | controller-0 | enabled-active |
| 2 | management-ip | controller-0 | enabled-active |
| 20 | mtc-agent | controller-0 | enabled-active |
| 28 | neutron-server | controller-0 | enabled-active |
| 9 | nfs-mgmt | controller-0 | enabled-active |
| 29 | nova-api | controller-0 | enabled-active |
| 63 | nova-api-proxy | controller-0 | enabled-active |
| 31 | nova-conductor | controller-0 | enabled-active |
| 33 | nova-console-auth | controller-0 | enabled-active |
| 34 | nova-novnc | controller-0 | enabled-active |
| 83 | nova-placement-api | controller-0 | enabled-active |
| 30 | nova-scheduler | controller-0 | enabled-active |
| 48 | open-ldap | controller-0 | enabled-active |
| 82 | panko-api | controller-0 | enabled-active |
| 52 | patch-alarm-manager | controller-0 | enabled-active |
| 7 | pg-fs | controller-0 | enabled-active |
| 15 | platform-export-fs | controller-0 | enabled-active |
| 11 | platform-fs | controller-0 | enabled-active |
| 17 | platform-nfs-ip | controller-0 | enabled-active |
| 12 | postgres | controller-0 | enabled-active |
| 65 | pxeboot-ip | controller-0 | enabled-active |
| 13 | rabbit | controller-0 | enabled-active |
| 8 | rabbit-fs | controller-0 | enabled-active |
| 49 | snmp | controller-0 | enabled-active |
| 19 | sysinv-conductor | controller-0 | enabled-active |
| 18 | sysinv-inv | controller-0 | enabled-active |
| 59 | vim | controller-0 | enabled-active |
| 60 | vim-api | controller-0 | enabled-active |
| 61 | vim-webserver | controller-0 | enabled-active |
+-----+-------------------------------+--------------+----------------+
As you can see, I cannot find #1 service (oam-ip), and I think this is one of the main reasons.
And also I had a problem when I followed the installation instruction.
[wrsroot at controller-0 ~(keystone_admin)]$ neutron providernet-create providernet-a --type=vlan
[wrsroot at controller-0 ~(keystone_admin)]$ neutron providernet-range-create --name providernet-a-range1 --range 100-400 providernet-a
[wrsroot at controller-0 ~(keystone_admin)]$ system host-if-modify -c data controller-0 eth1000 -p providernet-a
Above instruction was not naturally worked, I mean the third command, 'host-if-modify' failed with the message "DataNetwork providernet-a could not be found."
So I googled and I figured out I should command
$ system datanetwork-add providernet-a vlan
first.
But I remember when my first deployment succeed, I didn't need to use that command at all. (The deployment was implemented on Jan.)
Any help is appreciated, thank you for your help in advance.
Best Regards,
Jaewook.
================================================
Jaewook Oh (오재욱)
IISTRC - Internet Infra System Technology Research Center
369 Sangdo-ro, Dongjak-gu,
06978, Seoul, Republic of Korea
--
================================================
Jaewook Oh (오재욱)
IISTRC - Internet Infra System Technology Research Center
369 Sangdo-ro, Dongjak-gu,
06978, Seoul, Republic of Korea
--
================================================
Jaewook Oh (오재욱)
IISTRC - Internet Infra System Technology Research Center
369 Sangdo-ro, Dongjak-gu,
06978, Seoul, Republic of Korea
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.starlingx.io/pipermail/starlingx-discuss/attachments/20190219/080a9454/attachment-0001.html>
More information about the Starlingx-discuss
mailing list