[Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore

[Marcel Schaible]

Hi,

I am trying to give the above mentioned ISO image a try on our ArteSyn/MaxCore box without success.

After starting the installation I'll get the following message:

[   18.503656] localhost iscsid[643]: iSCSI daemon with pid=644 started!
[   18.503816] localhost iscsid[643]: can't open InitiatorName configuration file /etc/iscsi/initiatorname.iscsi
[   18.503949] localhost iscsid[643]: Warning: InitiatorName file /etc/iscsi/initiatorname.iscsi does not exist or does not contain a properly formatted InitiatorName. If using software iscsi (iscsi_tcp or ib_iser) or partial offload (bnx2i or cxgbi iscsi), you may not be able to log into or
[   18.504121] localhost iscsid[643]: can't open InitiatorAlias configuration file /etc/iscsi/initiatorname.iscsi
[   18.504254] localhost iscsid[643]: can't open iscsid.safe_logout configuration file /etc/iscsi/iscsid.conf
[   21.185105] localhost kernel: scsi 0:0:0:0: Direct-Access     Generic  Ultra HS-COMBO   1.98 PQ: 0 ANSI: 0
[   21.204488] localhost kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk
[   18.665925] localhost multipathd[636]: sda: add path (uevent)
[   18.667242] localhost multipathd[636]: sda: failed to get path uid
[   18.667399] localhost multipathd[636]: uevent trigger error
[   21.930592] localhost kernel: scsi 1:0:0:0: Direct-Access     TrekStor TrekStor USB CS       PQ: 0 ANSI: 0 CCS
[   21.940187] localhost kernel: scsi 1:0:0:0: alua: supports implicit and explicit TPGS
[   21.947210] localhost kernel: scsi 1:0:0:0: alua: No target port descriptors found
[   21.953921] localhost kernel: scsi 1:0:0:0: alua: not attached
[   21.959034] localhost kernel: sd 1:0:0:0: [sdb] 15257600 512-byte logical blocks: (7.81 GB/7.27 GiB)
[   21.968220] localhost kernel: sd 1:0:0:0: [sdb] Write Protect is off
[   21.973575] localhost kernel: sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00
[   21.974314] localhost kernel: sd 1:0:0:0: [sdb] No Caching mode page found
[   21.980260] localhost kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through
[   21.990203] localhost kernel:  sdb: sdb1
[   21.994973] localhost kernel: sd 1:0:0:0: [sdb] Attached SCSI removable disk
[   19.533105] localhost multipathd[636]: sdb: add path (uevent)
[   63.961502] localhost kernel: random: crng init done
[  142.536373] localhost dracut-initqueue[646]: Warning: dracut-initqueue timeout - starting timeout scripts
...
[  203.386668] localhost dracut-initqueue[646]: Warning: Could not boot.
[  204.505706] localhost systemd[1]: Received SIGRTMIN+20 from PID 625 (plymouthd).
[  204.505980] localhost dracut-initqueue[646]: Warning: /dev/root does not exist
[  204.514883] localhost systemd[1]: Starting Dracut Emergency Shell...
[  204.532145] localhost systemd[1]: Received SIGRTMIN+21 from PID 625 (plymouthd).

I suspect that the installer is not finding the disk, which is in our case nvme0n1 and nvme1n1 flash storage.

Any idea or hint is welcome!

Thanks

Marcel