[Starlingx-discuss] Deployment Option (error: compute boot in loop)
MacDonald, Eric
Eric.MacDonald at windriver.com
Mon Jan 28 14:33:12 UTC 2019
From the logs it looks like compute enabled fine this time but then failed shortly after due to intermittent heartbeat loss.
The stages are …
First mtcAlive with no indication of config failure ; a good thing
2019-01-28T12:22:15.430 [44890.06760] controller-0 mtcAgent |-| mtcNodeHdlrs.cpp (1056) enable_handler : Info : compute-0 is MTCALIVE (uptime:235 secs)
2019-01-28T12:22:15.430 fmAPI.cpp(471): Enqueue raise alarm request: UUID (c698824d-0d3e-42f0-a7a6-f705403ac8fe) alarm id (200.022) instant id (host=compute-0.status=online)
Out-Of-Service In-Test passed ; a good thing
2019-01-28T12:22:15.430 [44890.06761] controller-0 mtcAgent inv mtcInvApi.cpp (1085) mtcInvApi_update_state : Info : compute-0 intest (seq:19)
2019-01-28T12:22:27.557 [44890.06764] controller-0 mtcAgent |-| mtcNodeHdlrs.cpp (1172) enable_handler : Info : compute-0 got GOENABLED
Starting of local host services passed ; a good thing
2019-01-28T12:22:27.562 [44890.06766] controller-0 mtcAgent |-| mtcNodeHdlrs.cpp (1212) enable_handler : Info : compute-0 Starting Host Services
2019-01-28T12:22:27.628 [44890.06769] controller-0 mtcAgent hdl mtcNodeHdlrs.cpp (2586) host_services_handler : Info : compute-0 start compute host services completed
Heartbeat client was immediately ready as expected ; a good thing
2019-01-28T12:22:28.253 [44890.06770] controller-0 mtcAgent |-| nodeClass.cpp (4717) declare_service_ready : Info : compute-0 got hbsClient ready event
Heartbeat start and 11 second trial soak passed ; a good thing
2019-01-28T12:22:28.253 [44890.06771] controller-0 mtcAgent msg mtcCtrlMsg.cpp ( 804) send_hbs_command : Info : compute-0 sending 'start' to heartbeat service
2019-01-28T12:22:28.253 [44890.06772] controller-0 mtcAgent |-| mtcNodeHdlrs.cpp (1327) enable_handler : Info : compute-0 Starting 11 sec Heartbeat Soak (with ready event)
2019-01-28T12:22:39.253 [44890.06773] controller-0 mtcAgent |-| mtcNodeHdlrs.cpp (1341) enable_handler : Info : compute-0 heartbeating
Compute-0 Enabled ok ; very good thing
2019-01-28T12:22:39.502 [44890.06778] controller-0 mtcAgent |-| mtcNodeHdlrs.cpp (1488) enable_handler : Info : compute-0 is ENABLE
Intermittent heartbeat loss starts.
The after ~ 4 minutes compute-0 started experiencing Management network heartbeat loss
2019-01-28T12:26:58.819 [44890.06781] controller-0 mtcAgent --- nodeClass.cpp (4613) manage_heartbeat_degrade: Warn : compute-0 Mgmnt *** Heartbeat Miss ***
2019-01-28T12:26:59.257 [44890.06792] controller-0 mtcAgent hdl mtcNodeHdlrs.cpp (1637) recovery_handler : Info : compute-0 requesting mtcAlive with 5 sec timeout
2019-01-28T12:26:59.257 [44890.06794] controller-0 mtcAgent hdl mtcNodeHdlrs.cpp (1655) recovery_handler : Info : compute-0 got requested mtcAlive
Tries the 11 second heartbeat soak again after getting the requested mtcAlive message
2019-01-28T12:26:59.257 [44890.06795] controller-0 mtcAgent |-| nodeClass.cpp (2480) stop_offline_handler : Info : compute-0 stopping offline handler (unlocked-enabled-failed) (stage:3)
2019-01-28T12:26:59.257 [44890.06796] controller-0 mtcAgent hdl mtcNodeHdlrs.cpp (1722) recovery_handler : Warn : compute-0 Connectivity Recovered ; host did not reset
2019-01-28T12:26:59.257 [44890.06797] controller-0 mtcAgent hdl mtcNodeHdlrs.cpp (1724) recovery_handler : Warn : compute-0 ... continuing with graceful recovery
2019-01-28T12:26:59.257 [44890.06798] controller-0 mtcAgent hdl mtcNodeHdlrs.cpp (1725) recovery_handler : Warn : compute-0 ... with no affect to host services
2019-01-28T12:26:59.257 [44890.06799] controller-0 mtcAgent msg mtcCtrlMsg.cpp ( 804) send_hbs_command : Info : compute-0 sending 'start' to heartbeat service
2019-01-28T12:26:59.257 [44890.06800] controller-0 mtcAgent |-| mtcNodeHdlrs.cpp (2389) recovery_handler : Info : compute-0 Starting 11 sec Heartbeat Soak (with ready event)
The heartbeat loss is intermittent
After first loss the recovery tried the 11 second soak again that failed
2019-01-28T12:26:59.982 [44890.06802] controller-0 mtcAgent --- nodeClass.cpp (4613) manage_heartbeat_degrade: Warn : compute-0 Mgmnt *** Heartbeat Miss ***
2019-01-28T12:27:00.403 [44890.06803] controller-0 mtcAgent --- nodeClass.cpp (4495) manage_heartbeat_failure:Error : compute-0 Mgmnt *** Heartbeat Loss ***
2019-01-28T12:27:00.403 [44890.06804] controller-0 mtcAgent --- nodeClass.cpp (4506) manage_heartbeat_failure:Error : compute-0 Mgmnt network heartbeat failure
2019-01-28T12:27:00.403 [44890.06805] controller-0 mtcAgent --- nodeClass.cpp (4515) manage_heartbeat_failure: Warn : compute-0 restarting graceful recovery
2019-01-28T12:27:00.403 [44890.06806] controller-0 mtcAgent |-| mtcNodeHdlrs.cpp (1557) recovery_handler : Info : compute-0 Graceful Recovery (uptime was 519)
Heartbeat seems intermittent because the recovery algorithm reached its retry threshold of 3 and force failed the node
2019-01-28T12:27:01.556 [44890.06828] controller-0 mtcAgent hdl mtcNodeHdlrs.cpp (1592) recovery_handler :Error : compute-0 Graceful Recovery Failed (retries=3
2019-01-28T12:27:01.556 [44890.06829] controller-0 mtcAgent |-| nodeClass.cpp (7193) force_full_enable : Info : compute-0 Forcing Full Enable Sequence
2019-01-28T12:27:01.556 [44890.06830] controller-0 mtcAgent --- nodeClass.cpp (1644) alarm_enabled_failure :Error : compute-0 critical enable failure
The force failure caused a reboot and recovery retry where the logs ended.
Sequence will likely continue until the heartbeat (potentially multicast) issue is fixed.
Based on you saying that with the switch removed heartbeat passed I’d look at how the switch or your management network is handling multicast messaging and if the QOS settings on the network might be dropping packets.
Eric.
From: Himanshu Goyal [mailto:himanshugoyal500 at gmail.com]
Sent: Monday, January 28, 2019 3:56 AM
To: MacDonald, Eric
Cc: Peters, Matt; starlingx-discuss at lists.starlingx.io
Subject: Re: [Starlingx-discuss] Deployment Option (error: compute boot in loop)
Importance: High
Hi Eric,
That compute reboot issue is resolved, I connect controller & compute connection directly without switch in between after unlock.
I don't know why it is not working with switch after unlock, Please check there is only hear-beat issue on mgmt network or something else, currently i'm using only 1 compute so its fine.
Regards,
Himanshu Goyal
On Mon, Jan 28, 2019 at 12:33 PM Himanshu Goyal <himanshugoyal500 at gmail.com<mailto:himanshugoyal500 at gmail.com>> wrote:
Hi Eric,
Please find attached required mtcAgent.log containing one cycle of compute from PXE boot to unlock.
Regards,
Himanshu Goyal
On Fri, Jan 25, 2019 at 10:12 PM Himanshu Goyal <himanshugoyal500 at gmail.com<mailto:himanshugoyal500 at gmail.com>> wrote:
Sure Eric, currently i have left for the day, i will get back to you first thing on Monday morning.
Many Thanks,
Himanshu Goyal
On Fri, Jan 25, 2019 at 8:17 PM MacDonald, Eric <Eric.MacDonald at windriver.com<mailto:Eric.MacDonald at windriver.com>> wrote:
Hi Himanshu,
The mtcAgent.log shows that compute-0 has experienced the following errors several times over the span of almost 3 days.
Configuration failures
2019-01-24T12:30:34.764 [44890.04799] controller-0 mtcAgent hdl mtcNodeHdlrs.cpp (1046) enable_handler :Error : compute-0 configuration incomplete or failed (oob:2:1)
2019-01-24T12:30:34.764 [44890.04800] controller-0 mtcAgent --- nodeClass.cpp (1606) alarm_config_failure :Error : compute-0 critical config failure
2019-01-24T12:30:34.764 [44890.04801] controller-0 mtcAgent alm mtcAlarm.cpp ( 417) mtcAlarm_critical :Error : compute-0 setting critical 'Configuration' failure alarm (200.011
Out-Of-Service GoEnable Test Failures
2019-01-24T12:00:56.186 [44890.04700] controller-0 mtcAgent hdl mtcNodeHdlrs.cpp (1163) enable_handler :Error : compute-0 got GOENABLED
Experiencing Management network heartbeat failures.
2019-01-23T15:03:44.535 [44890.01949] controller-0 mtcAgent --- nodeClass.cpp (4506) manage_heartbeat_failure:Error : compute-0 Mgmnt network heartbeat failure
2019-01-23T15:03:45.688 [44890.01967] controller-0 mtcAgent --- nodeClass.cpp (4495) manage_heartbeat_failure:Error : compute-0 Mgmnt *** Heartbeat Loss **
Since compute-0 is locked the in-service alarms against it will be suppressed.
Since there are many errors over time I would recommend tailing the mtcAgent.log file to a new small file you can send to me. This file would contain all the logs that are produced for one cycle of an unlock of compute-0
This way we can focus on one case at a time.
Eric.
From: Himanshu Goyal [mailto:himanshugoyal500 at gmail.com<mailto:himanshugoyal500 at gmail.com>]
Sent: Friday, January 25, 2019 9:31 AM
To: MacDonald, Eric
Cc: Peters, Matt; starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>
Subject: Re: [Starlingx-discuss] Deployment Option (error: compute boot in loop)
Importance: High
Hi Eric,
Below are required outputs of commands:
fm alarm-list
######################################################
[root at controller-0 wrsroot(keystone_admin)]# fm alarm-list
+-------+---------------------------------------------------------------------------------+--------------------------------------+----------+----------------+
| Alarm | Reason Text | Entity ID | Severity | Time Stamp |
| ID | | | | |
+-------+---------------------------------------------------------------------------------+--------------------------------------+----------+----------------+
| 200. | compute-0 was administratively locked to take it out-of-service. | host=compute-0 | warning | 2019-01-25T15: |
| 001 | | | | 00:12.159130 |
| | | | | |
| 300. | No enabled compute host with connectivity to provider network. | service=networking.providernet= | major | 2019-01-25T14: |
| 004 | | 4dbbc02e-c93c-494e-bd8d-1706eb09a3a6 | | 58:56.711665 |
| | | | | |
| 400. | Service group cloud-services loss of redundancy; expected 1 standby member but | service_domain=controller. | major | 2019-01-22T19: |
| 002 | no standby members available | service_group=cloud-services | | 12:07.245142 |
| | | | | |
| 400. | Service group controller-services loss of redundancy; expected 1 standby member | service_domain=controller. | major | 2019-01-22T19: |
| 002 | but no standby members available | service_group=controller-services | | 11:40.174144 |
| | | | | |
| 400. | Service group vim-services loss of redundancy; expected 1 standby member but no | service_domain=controller. | major | 2019-01-22T19: |
| 002 | standby members available | service_group=vim-services | | 11:39.052152 |
| | | | | |
| 400. | Service group oam-services loss of redundancy; expected 1 standby member but no | service_domain=controller. | major | 2019-01-22T19: |
| 002 | standby members available | service_group=oam-services | | 11:38.728175 |
| | | | | |
| 400. | Service group patching-services loss of redundancy; expected 1 standby member | service_domain=controller. | major | 2019-01-22T19: |
| 002 | but no standby members available | service_group=patching-services | | 11:37.756169 |
| | | | | |
| 400. | Service group directory-services loss of redundancy; expected 2 active members | service_domain=controller. | major | 2019-01-22T19: |
| 002 | but only 1 active member available | service_group=directory-services | | 11:37.513178 |
| | | | | |
| 400. | Service group web-services loss of redundancy; expected 2 active members but | service_domain=controller. | major | 2019-01-22T19: |
| 002 | only 1 active member available | service_group=web-services | | 11:37.189196 |
| | | | | |
| 400. | Communication failure detected with peer over port bond0 on host controller-0 | host=controller-0.network=mgmt | major | 2019-01-22T19: |
| 005 | | | | 11:36.690138 |
| | | | | |
| 400. | Communication failure detected with peer over port bond1 on host controller-0 | host=controller-0.network=oam | major | 2019-01-22T19: |
| 005 | | | | 11:36.427073 |
| | | | | |
+-------+---------------------------------------------------------------------------------+--------------------------------------+----------+----------------+
[root at controller-0 wrsroot(keystone_admin)]#
#########################################################################################################
Please find attached file for fgrep Error /var/log/mtcAgent.log output
Regards,
Himanshu Goyal
On Fri, Jan 25, 2019 at 7:43 PM MacDonald, Eric <Eric.MacDonald at windriver.com<mailto:Eric.MacDonald at windriver.com>> wrote:
fgrep Error /var/log/mtcAgent.log
fm alarm-list
From: Peters, Matt [mailto:Matt.Peters at windriver.com<mailto:Matt.Peters at windriver.com>]
Sent: Friday, January 25, 2019 8:05 AM
To: Himanshu Goyal
Cc: starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>
Subject: Re: [Starlingx-discuss] Deployment Option (error: compute boot in loop)
The DPDK and OVS status look fine now.
I would check the /var/log/mtcAgent.log on the active controller host to determine what is being reported for the reboot.
From: Himanshu Goyal <himanshugoyal500 at gmail.com<mailto:himanshugoyal500 at gmail.com>>
Date: Friday, January 25, 2019 at 3:56 AM
To: "Peters, Matt" <Matt.Peters at windriver.com<mailto:Matt.Peters at windriver.com>>
Cc: "Hu, Yong" <yong.hu at intel.com<mailto:yong.hu at intel.com>>, "starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>" <starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>>
Subject: Re: [Starlingx-discuss] Deployment Option (error: compute boot in loop)
Hi Matt,
Please find below output of dpdk-devbind.py --status also:
compute-0:/var/log/puppet/latest# python /usr/share/openvswitch/scripts/dpdk-devbind.py --status
##########################################################################################################
python /usr/share/openvswitch/scripts/dpdk-devbind.py --status
Network devices using DPDK-compatible driver
============================================
0000:04:00.0 'I350 Gigabit Network Connection 1521' drv=vfio-pci unused=
Network devices using kernel driver
===================================
0000:02:00.1 '82599ES 10-Gigabit SFI/SFP+ Network Connection 10fb' if=ens513f1 drv=ixgbe unused=vfio-pci
0000:04:00.3 'I350 Gigabit Network Connection 1521' if=enp4s0f3 drv=igb unused=vfio-pci *Active*
Other Network devices
=====================
0000:02:00.0 '82599ES 10-Gigabit SFI/SFP+ Network Connection 10fb' unused=vfio-pci
Crypto devices using DPDK-compatible driver
===========================================
<none>
Crypto devices using kernel driver
==================================
<none>
Other Crypto devices
====================
<none>
Eventdev devices using DPDK-compatible driver
=============================================
<none>
Eventdev devices using kernel driver
====================================
<none>
Other Eventdev devices
======================
<none>
Mempool devices using DPDK-compatible driver
============================================
<none>
Mempool devices using kernel driver
===================================
<none>
Other Mempool devices
=====================
<none>
compute-0:/var/log/puppet/latest#
################################################################################
Regards,
Himanshu Goyal
On Fri, Jan 25, 2019 at 2:14 PM Himanshu Goyal <himanshugoyal500 at gmail.com<mailto:himanshugoyal500 at gmail.com>> wrote:
Hi Matt,
Sorry, interrupt remapping was disabled in my BIOS, I tried again after enable that, Now in dmesg & ovs-vsct there is no errors. But compute still rebooting in loop.
Please find attached dmesg log output for reference.
#######################################################################
compute-0:/home/wrsroot# sudo ovs-vsctl show
8a1f7179-2014-4b4e-ad23-2065b8024964
Manager "ptcp:6640:127.0.0.1"
is_connected: true
Bridge "br-phy0"
Controller "tcp:127.0.0.1:6633<http://127.0.0.1:6633>"
is_connected: true
fail_mode: secure
Port "lldp64416a6d-7d"
Interface "lldp64416a6d-7d"
type: internal
Port "phy-br-phy0"
Interface "phy-br-phy0"
type: patch
options: {peer="int-br-phy0"}
Port "br-phy0"
Interface "br-phy0"
type: internal
Port "eth0"
Interface "eth0"
type: dpdk
options: {dpdk-devargs="0000:04:00.0", n_rxq="2"}
Bridge br-int
Controller "tcp:127.0.0.1:6633<http://127.0.0.1:6633>"
is_connected: true
fail_mode: secure
Port br-int
Interface br-int
type: internal
Port "int-br-phy0"
Interface "int-br-phy0"
type: patch
options: {peer="phy-br-phy0"}
ovs_version: "2.9.0"
compute-0:/home/wrsroot#
#############################################################################
Please suggest me any other logs that i can check.
Regards,
Himanshu Goyal
On Fri, Jan 25, 2019 at 12:21 PM Himanshu Goyal <himanshugoyal500 at gmail.com<mailto:himanshugoyal500 at gmail.com>> wrote:
Thanks Matt,
Below are the details of my server BIOS, Currently in my Server Bios Version: SE5C610.86B.01.01.0014.121820151719,
Please suggest which version of Bios we can use & this version is up-gradable or not with required version.
#################################################################
compute-0:/home/wrsroot# dmidecode -t1
# dmidecode 3.0
Getting SMBIOS data from sysfs.
SMBIOS 2.7 present.
Handle 0x0001, DMI type 1, 27 bytes
System Information
Manufacturer: Intel Corporation
Product Name: S2600WT2
Version: ....................
Serial Number: ............
UUID: 803BBEFB-BFC1-E511-906E-0012795D96DD
Wake-up Type: Power Switch
SKU Number: SKU Number
Family: Family
#############################################################################
################################################################################
compute-0:/home/wrsroot# sudo dmidecode --type bios
# dmidecode 3.0
Getting SMBIOS data from sysfs.
SMBIOS 2.7 present.
Handle 0x0000, DMI type 0, 24 bytes
BIOS Information
Vendor: Intel Corporation
Version: SE5C610.86B.01.01.0014.121820151719
Release Date: 12/18/2015
Address: 0xF0000
Runtime Size: 64 kB
ROM Size: 16384 kB
Characteristics:
PCI is supported
PNP is supported
BIOS is upgradeable
BIOS shadowing is allowed
Boot from CD is supported
Selectable boot is supported
EDD is supported
5.25"/1.2 MB floppy services are supported (int 13h)
3.5"/720 kB floppy services are supported (int 13h)
3.5"/2.88 MB floppy services are supported (int 13h)
Print screen service is supported (int 5h)
8042 keyboard services are supported (int 9h)
Serial services are supported (int 14h)
Printer services are supported (int 17h)
CGA/mono video services are supported (int 10h)
ACPI is supported
USB legacy is supported
LS-120 boot is supported
ATAPI Zip drive boot is supported
BIOS boot specification is supported
Function key-initiated network boot is supported
Targeted content distribution is supported
UEFI is supported
BIOS Revision: 0.0
Firmware Revision: 0.0
Handle 0x000B, DMI type 13, 22 bytes
BIOS Language Information
Language Description Format: Abbreviated
Installable Languages: 1
enUS
Currently Installed Language: enUS
########################################################################################################
Regards,
Himanshu Goyal
On Thu, Jan 24, 2019 at 10:55 PM Peters, Matt <Matt.Peters at windriver.com<mailto:Matt.Peters at windriver.com>> wrote:
Based on the logs, it looks like you have an older system that doesn’t fully support VT-d IOMMU remapping. You can try updating your BIOS if there is a newer version available. We don’t currently support setting arbitrary module parameters, so we don’t have a way to implement the workaround module param specified in the logs (i.e. disabling interrupt remapping).
Maybe there are others on the distribution list that could offer additional suggestions.
From: Himanshu Goyal <himanshugoyal500 at gmail.com<mailto:himanshugoyal500 at gmail.com>>
Date: Thursday, January 24, 2019 at 11:32 AM
To: "Peters, Matt" <Matt.Peters at windriver.com<mailto:Matt.Peters at windriver.com>>
Cc: "Hu, Yong" <yong.hu at intel.com<mailto:yong.hu at intel.com>>, "starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>" <starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>>
Subject: Re: [Starlingx-discuss] Deployment Option (error: compute boot in loop)
Hi Peters,
Please find output of required command in attached file.
Regards,
Himanshu Goyal
Regards,
Himanshu Goyal
On Thu, Jan 24, 2019 at 6:56 PM Peters, Matt <Matt.Peters at windriver.com<mailto:Matt.Peters at windriver.com>> wrote:
Can you confirm that VT-d is enabled properly by running the following?
dmesg | grep -i -e DMAR -e IOMMU
From: Himanshu Goyal <himanshugoyal500 at gmail.com<mailto:himanshugoyal500 at gmail.com>>
Date: Thursday, January 24, 2019 at 8:19 AM
To: "Peters, Matt" <Matt.Peters at windriver.com<mailto:Matt.Peters at windriver.com>>
Cc: "Hu, Yong" <yong.hu at intel.com<mailto:yong.hu at intel.com>>, "starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>" <starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>>
Subject: Re: [Starlingx-discuss] Deployment Option (error: compute boot in loop)
Hi Peters,
Error logs ovs-vswitched.log:
#######################################
2019-01-24T18:42:04.213Z|00830|dpdk|INFO|EAL: PCI device 0000:02:00.0 on NUMA socket 0
2019-01-24T18:42:04.213Z|00831|dpdk|INFO|EAL: probe driver: 8086:10fb net_ixgbe
2019-01-24T18:42:04.215Z|00832|dpdk|ERR|EAL: 0000:02:00.0 failed to select IOMMU type
2019-01-24T18:42:04.215Z|00833|dpdk|ERR|EAL: Driver cannot attach the device (0000:02:00.0)
2019-01-24T18:42:04.215Z|00834|netdev_dpdk|WARN|Error attaching device '0000:02:00.0' to DPDK
2019-01-24T18:42:04.215Z|00835|netdev|WARN|eth0: could not set configuration (Invalid argument)
########################################
Please find attached log file also.
Regards,
Himanshu Goyal
On Thu, Jan 24, 2019 at 6:32 PM Peters, Matt <Matt.Peters at windriver.com<mailto:Matt.Peters at windriver.com>> wrote:
The name of eth0 is correct. It is just an assigned name by configuration management.
What err logs are present in /var/log/openvswitch/ovs-vswitchd.log?
From: Himanshu Goyal <himanshugoyal500 at gmail.com<mailto:himanshugoyal500 at gmail.com>>
Date: Thursday, January 24, 2019 at 6:52 AM
To: "Hu, Yong" <yong.hu at intel.com<mailto:yong.hu at intel.com>>
Cc: "starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>" <starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>>
Subject: Re: [Starlingx-discuss] Deployment Option (error: compute boot in loop)
Thanks a lot Yong,
Checked OVS/DPDK status, It is giving me the error as output shown below:
In br-phy0 is attaching a port name as eth0, but my compute port name is ens513f0, i think that may be the issue.
#################################################################################
ovs-vsctl show output:
compute-0:/usr/share/openvswitch/scripts$ sudo ovs-vsctl show
543d08f4-ff1e-4a8d-8e48-11f01356750d
Manager "ptcp:6640:127.0.0.1"
is_connected: true
Bridge "br-phy0"
Controller "tcp:127.0.0.1:6633<http://127.0.0.1:6633>"
is_connected: true
fail_mode: secure
Port "phy-br-phy0"
Interface "phy-br-phy0"
type: patch
options: {peer="int-br-phy0"}
Port "br-phy0"
Interface "br-phy0"
type: internal
Port "lldpabeb30a6-6c"
Interface "lldpabeb30a6-6c"
type: internal
Port "eth0"
Interface "eth0"
type: dpdk
options: {dpdk-devargs="0000:02:00.0", n_rxq="2"}
error: "Error attaching device '0000:02:00.0' to DPDK"
Bridge br-int
Controller "tcp:127.0.0.1:6633<http://127.0.0.1:6633>"
is_connected: true
fail_mode: secure
Port "int-br-phy0"
Interface "int-br-phy0"
type: patch
options: {peer="phy-br-phy0"}
Port br-int
Interface br-int
type: internal
ovs_version: "2.9.0"
#####################################################################################################
##############################################################################
Output of dpdk-devbind.py:
compute-0:/usr/share/openvswitch/scripts$ python /usr/share/openvswitch/scripts/dpdk-devbind.py --status
Network devices using DPDK-compatible driver
============================================
0000:02:00.0 '82599ES 10-Gigabit SFI/SFP+ Network Connection 10fb' drv=vfio-pci unused=
Network devices using kernel driver
===================================
0000:02:00.1 '82599ES 10-Gigabit SFI/SFP+ Network Connection 10fb' if=ens513f1 drv=ixgbe unused=vfio-pci *Active*
0000:04:00.0 'I350 Gigabit Network Connection 1521' if=enp4s0f0 drv=igb unused=vfio-pci
0000:04:00.3 'I350 Gigabit Network Connection 1521' if=enp4s0f3 drv=igb unused=vfio-pci
Other Network devices
=====================
<none>
Crypto devices using DPDK-compatible driver
===========================================
<none>
Crypto devices using kernel driver
==================================
<none>
Other Crypto devices
====================
<none>
Eventdev devices using DPDK-compatible driver
=============================================
<none>
Eventdev devices using kernel driver
====================================
<none>
Other Eventdev devices
======================
<none>
Mempool devices using DPDK-compatible driver
============================================
<none>
Mempool devices using kernel driver
===================================
<none>
Other Mempool devices
=====================
<none>
compute-0:/usr/share/openvswitch/scripts$
#############################################################
Both management and OAM ports support DPDK.
lspci output:
##################################################
compute-0:/usr/share/openvswitch/scripts$ lspci -nn | grep Eth
02:00.0 Ethernet controller [0200]: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection [8086:10fb] (rev 01)
02:00.1 Ethernet controller [0200]: Intel Corporation 82599ES 10-Gigabit SFI/SFP+ Network Connection [8086:10fb] (rev 01)
04:00.0 Ethernet controller [0200]: Intel Corporation I350 Gigabit Network Connection [8086:1521] (rev 01)
04:00.3 Ethernet controller [0200]: Intel Corporation I350 Gigabit Network Connection [8086:1521] (rev 01)
###############################################################
compute-0:/usr/share/openvswitch/scripts$
Many Thanks,
Himanshu Goyal
On Thu, Jan 24, 2019 at 2:24 PM Hu, Yong <yong.hu at intel.com<mailto:yong.hu at intel.com>> wrote:
I saw you enabled VT-D, how about VT-x in BIOS?
Another possibility is that your ethernet NIC is not compatible with OVS/DPDK.
Please follow these steps, to dig out more info
1. lock your compute-node
2. ssh to your compute-node and check OVS/DPDK status by “sudo ovs-vsctl show” and “python /usr/share/openvswitch/scripts/dpdk-devbind.py --status”
From: Himanshu Goyal <himanshugoyal500 at gmail.com<mailto:himanshugoyal500 at gmail.com>>
Date: Thursday, 24 January 2019 at 4:46 PM
To: "Hu, Yong" <yong.hu at intel.com<mailto:yong.hu at intel.com>>
Cc: "Alonso, Juan Carlos" <juan.carlos.alonso at intel.com<mailto:juan.carlos.alonso at intel.com>>, "starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>" <starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>>
Subject: Re: [Starlingx-discuss] Deployment Option (error: compute boot in loop)
Hi Yong,
I checked server BIOS setting Intel VT-D is enabled in my compute machine
compute machine is rebooting only after unlocking, Before reboot it came in unlocked, enabled & online.
Please suggest how can i debug this.
Many Thanks,
Himanshu Goyal
On Wed, Jan 23, 2019 at 9:40 PM Hu, Yong <yong.hu at intel.com<mailto:yong.hu at intel.com>> wrote:
Intel_iommu=on and immmu are for PCI PT and SR-IOV, as far as I know.
There are other 2, like VT-x and VT-d flags, to be enabled. Please have a look in BIOS.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.starlingx.io/pipermail/starlingx-discuss/attachments/20190128/3cfc6ce5/attachment-0001.html>
More information about the Starlingx-discuss
mailing list