[Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore

[Penney, Don]

Thanks Scott.

From: Little, Scott
Sent: Wednesday, January 09, 2019 3:55 PM
To: Penney, Don; Marcel Schaible; starlingx-discuss at lists.starlingx.io
Subject: Re: [Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore

Fix as of this image ...

http://mirror.starlingx.cengn.ca/mirror/starlingx/master/centos/20190109T162801Z/outputs/iso/bootimage.iso


On 2019-01-09 11:08 a.m., Penney, Don wrote:

I just checked the latest CENGN ISO, and it's still using the unmodified installer image. See attached email thread.



Scott, any update on this issue?



-----Original Message-----

From: Marcel Schaible [mailto:marcel at schaible-consulting.de]

Sent: Wednesday, January 09, 2019 10:24 AM

To: starlingx-discuss at lists.starlingx.io<mailto:starlingx-discuss at lists.starlingx.io>

Subject: [Starlingx-discuss] StarlingX ISO Image from Cengn Mirror not working on Artesyn/MaxCore



Hi,



I am trying to give the above mentioned ISO image a try on our ArteSyn/MaxCore box without success.



After starting the installation I'll get the following message:



[   18.503656] localhost iscsid[643]: iSCSI daemon with pid=644 started!

[   18.503816] localhost iscsid[643]: can't open InitiatorName configuration file /etc/iscsi/initiatorname.iscsi

[   18.503949] localhost iscsid[643]: Warning: InitiatorName file /etc/iscsi/initiatorname.iscsi does not exist or does not contain a properly formatted InitiatorName. If using software iscsi (iscsi_tcp or ib_iser) or partial offload (bnx2i or cxgbi iscsi), you may not be able to log into or

[   18.504121] localhost iscsid[643]: can't open InitiatorAlias configuration file /etc/iscsi/initiatorname.iscsi

[   18.504254] localhost iscsid[643]: can't open iscsid.safe_logout configuration file /etc/iscsi/iscsid.conf

[   21.185105] localhost kernel: scsi 0:0:0:0: Direct-Access     Generic  Ultra HS-COMBO   1.98 PQ: 0 ANSI: 0

[   21.204488] localhost kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk

[   18.665925] localhost multipathd[636]: sda: add path (uevent)

[   18.667242] localhost multipathd[636]: sda: failed to get path uid

[   18.667399] localhost multipathd[636]: uevent trigger error

[   21.930592] localhost kernel: scsi 1:0:0:0: Direct-Access     TrekStor TrekStor USB CS       PQ: 0 ANSI: 0 CCS

[   21.940187] localhost kernel: scsi 1:0:0:0: alua: supports implicit and explicit TPGS

[   21.947210] localhost kernel: scsi 1:0:0:0: alua: No target port descriptors found

[   21.953921] localhost kernel: scsi 1:0:0:0: alua: not attached

[   21.959034] localhost kernel: sd 1:0:0:0: [sdb] 15257600 512-byte logical blocks: (7.81 GB/7.27 GiB)

[   21.968220] localhost kernel: sd 1:0:0:0: [sdb] Write Protect is off

[   21.973575] localhost kernel: sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00

[   21.974314] localhost kernel: sd 1:0:0:0: [sdb] No Caching mode page found

[   21.980260] localhost kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through

[   21.990203] localhost kernel:  sdb: sdb1

[   21.994973] localhost kernel: sd 1:0:0:0: [sdb] Attached SCSI removable disk

[   19.533105] localhost multipathd[636]: sdb: add path (uevent)

[   63.961502] localhost kernel: random: crng init done

[  142.536373] localhost dracut-initqueue[646]: Warning: dracut-initqueue timeout - starting timeout scripts

...

[  203.386668] localhost dracut-initqueue[646]: Warning: Could not boot.

[  204.505706] localhost systemd[1]: Received SIGRTMIN+20 from PID 625 (plymouthd).

[  204.505980] localhost dracut-initqueue[646]: Warning: /dev/root does not exist

[  204.514883] localhost systemd[1]: Starting Dracut Emergency Shell...

[  204.532145] localhost systemd[1]: Received SIGRTMIN+21 from PID 625 (plymouthd).



I suspect that the installer is not finding the disk, which is in our case nvme0n1 and nvme1n1 flash storage.



Any idea or hint is welcome!



Thanks



Marcel



_______________________________________________

Starlingx-discuss mailing list

Starlingx-discuss at lists.starlingx.io<mailto:Starlingx-discuss at lists.starlingx.io>

http://lists.starlingx.io/cgi-bin/mailman/listinfo/starlingx-discuss


-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.starlingx.io/pipermail/starlingx-discuss/attachments/20190109/962d4376/attachment-0001.html>